User manual YAMAHA RX-V496

[. . . ] UCA RX-V496 Natural Sound AV Receiver Ampli-tuner audio-vidéo OWNER'S MANUAL MODE D'EMPLOI SAFETY INSTRUCTIONS 8 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Ventilation ­ The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, the unit should not be situated on a bed, sofa, rug, or similar surface, that may block the ventilation openings; or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. Heat ­ The unit should be situated away from heat sources such as radiators, stoves, or other appliances that produce heat. 9 · Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] This function enables the unit to automatically tune in with strong signals and to sequentially store up to 40 FM stations (5 groups x 8 stations). s Automatic preset tuning options You can select the preset number from which the unit will store FM stations and/or begin tuning toward lower frequencies. Before automatic preset tuning begins (after pressing MEMORY in step 3), 1. Press A/B/C/D/E and PRESET/TUNING to select the preset number with which the first station will be stored. The automatic preset tuning will stop when stations have all been stored up to E8. Press PRESET/TUNING (EDIT) to turn " z " off and then press PRESET/TUNING l to begin tuning toward lower frequencies. INTRODUCTION ­ + ­ + L R s When automatic preset tuning is completed 13 2 The display shows the frequency of the last preset station. Check the contents and the number of preset stations by following the procedure in the section "To Recall a Preset Station" on page 30. PREPARATION 1 Press FM/AM to select the FM band. Notes · A new setting can be stored in place of the former one. · You can manually replace a preset station with another FM or AM station by simply using the manual preset tuning method. · Even if the number of received stations is not enough to be stored up to E8, automatic preset tuning is automatically ended after searching for all stations. · Only FM stations with sufficient signal strength are stored by automatic preset tuning. If the station you want to store is weak in signal strength, tune in to it manually in monaural mode and store it by using the manual preset tuning method. BASIC OPERATION 2 Press TUNING MODE so that the "AUTO" indicator lights up on the display. Lights up 3 Hold down MEMORY for about three seconds. The preset number, the "MEMORY" and "AUTO" indicators flash. After about five seconds, automatic preset tuning begins from the frequency currently displayed toward the higher frequencies. Received stations are sequentially stored as A1, A2 . . . If more than 8 stations have been tuned, they are stored as preset station numbers in other groups (B, C, D and E) in that order. ADVANCED OPERATION Flashes Memory back-up The memory back-up circuit prevents the stored data from being lost when this unit is set in the standby mode. If, however, the power cord is disconnected from the AC power outlet or the power is cut for more than one week, the memory will be erased. If so, store the stations again by using preset tuning methods. APPENDIX English 29 TUNING Manual Preset Tuning You can also store up to 40 stations (5 groups x 8 stations) manually. To Recall a Preset Station You can recall any desired station simply by selecting the preset station number with which it was stored. You can also recall a preset station with the remote control. Press AMP(TUNER) on the component selector and press TUNER on the input selector. ­ + ­ + L R 3 4 2, 5 ­ + ­ + L R 1 2 Tune in to the desired station. Refer to page 28 for the tuning procedure. The "MEMORY" indicator flashes for about five seconds. 1 2 Flashes 3 Press A/B/C/D/E repeatedly to select the desired group (A to E) of preset stations before the "MEMORY" indicator goes off. Make sure that " z " appears on the display. The selected group appears on the display. 1 2 1 Press A/B/C/D/E to select the required group of preset stations. [. . . ] 34, 35 Speaker balance (test tone) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 STANDBY/ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 E External decoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]