User manual YAMAHA RX-V595

[. . . ] CA RX-V595 RX-V595 Natural Sound AV Receiver Récepteur audiovisuel OWNER'S MANUAL MODE D'EMPLOI YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE. , BUENA PARK, CALIF. 135 MILNER AVE. , SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G. m. b. H. 22-34, 25462 RELLINGEN BEI HAMBURG, F. R. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. [. . . ] · For presets, the setting of the reception mode (stereo or monaural) is stored along with the station frequency. Memory back-up The memory back-up circuit prevents the stored data from being lost even if this unit is turned into the standby mode, or the power plug is disconnected from the AC outlet, or the power is cut due to temporary power failure. If, however, the power is cut for more than one week, the memory may be erased. If so, it can be re-stored by simply following the preset tuning procedures. 33 01RX-V595-e/f3 33 6/23/99, 4:10 PM AUTOMATIC PRESET TUNING (For FM stations only) You can also make use of an automatic preset tuning function for FM stations only. Using this function, this unit performs automatic tuning and sequentially stores FM stations with strong signals. Up to 40 stations are stored automatically in the same way as in the manual preset tuning method on page 32. Note that a new setting can be stored in place of the former one. 31 24 To store stations 1 Select the FM. Front panel 4 To tune in to higher frequencies, press the UP side of TUNING once. To tune in to lower frequencies, press the DOWN side of TUNING once. Front panel 2 Press TUNING MODE (so that the "AUTO TUNING" indicator lights up on the display). Front panel * If TUNING is not pressed, in a while, the automatic preset tuning begins automatically toward higher frequencies. The automatic preset tuning begins from the frequency currently displayed. Received stations are stored to A1, A2 . . . * If more than 8 stations are received, they are also stored to the preset station numbers in other groups (B, C, D and E) in that order. Lights up. 3 Press MEMORY and hold for about three seconds. Front panel Flashes. If you want to store the first station received by the automatic preset tuning to a desired preset station number. For example, if you want to store the first received station to C5, select "C5" while "A1", the "MEMORY" indicator and the "AUTO TUNING" indicator flash after pressing MEMORY in step 3. The first received station is stored to C5, and next stations to C6, C7 . . . If stations are stored up to E8, automatic preset tuning stops automatically. When automatic preset tuning is finished The display shows the frequency of the last preset station. Check the contents and the number of preset stations by following the procedures in the section "To recall a preset station" on page 33. 34 01RX-V595-e/f3 34 6/23/99, 4:11 PM English Notes · You can replace a preset station with another FM or AM station manually by simply following the procedures in the section "To store stations" on page 32. · Even if the number of received stations is not enough to be stored up to E8, the search is finished automatically after searching all frequencies. · With this function, only FM stations with sufficient signal strength are stored automatically. If the station you want to store is weak in signal strength, tune in to it in monaural manually and store it by following the procedures in the section "To store stations" on page 32. EXCHANGING PRESET STATIONS You can exchange the places of two preset stations with each other as shown below. 2, 4 Example If you want to shift the preset station on E1 to A5, and vice versa. 1 2 Recall the preset station on E1 (by following the procedures in the section "To recall a preset station" on page 33). 3 Next, recall the preset station on A5 by following the same procedures as in step 1. Press EDIT. Front Panel Flashes. 4 Flashes. Press EDIT once more. Front Panel Shows the exchange of stations is completed. 35 01RX-V595-e/f3 35 6/23/99, 4:11 PM SETTING THE SLEEP TIMER If you use the SLEEP timer of this unit, you can make this unit automatically switch to the standby mode. When you are going to sleep while enjoying a broadcast or other desired input source, this timer function is useful. The SLEEP timer can be controlled only with the remote control transmitter. Notes · To set the SLEEP timer for this unit, set the SELECTOR DIAL to a position other than the TV postition. To set the SLEEP timer for your TV, set the SELECTOR DIAL to the TV position. · The components on which the SLEEP timer is effective are the sources connected to the SWITCHED AC OUTLET(S) on the rear panel of this unit. 1 To set the SLEEP time To cancel the selected SLEEP time Remote control 1 Press SLEEP once or more to select the desired SLEEP time. Remote control Press SLEEP once or more so that "SLEEP OFF" appears on the display. [. . . ] AC 220 V, 50 Hz [Singapore model] . . . . . . . . . . . . . AC 230 V, 50 Hz Power Consumption [U. S. A. model] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280 W [Canada model] . . . . . . . . . . . . . . . . . . . . [. . . ]