User manual YAMAHA RX-V596

[. . . ] UCA RX-V596 Natural Sound AV Receiver Ampli-tuner audio-vidéo OWNER'S MANUAL MODE D'EMPLOI SAFETY INSTRUCTIONS 8 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Ventilation ­ The unit should be situated so that its location or position does not interfere with its proper ventilation. For example, the unit should not be situated on a bed, sofa, rug, or similar surface, that may block the ventilation openings; or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings. Heat ­ The unit should be situated away from heat sources such as radiators, stoves, or other appliances that produce heat. 9 · Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] The displayed station has been stored as the preset group and number you have selected, and the reception band and frequency appear on the display. 2 5 Press PRESET/TUNING h or l (or PRESET +/­) to select a preset station number (1 to 8). The preset group and number appear on the display along with the reception band, frequency and signal strength information. or APPENDIX Front panel Remote control 6 Repeat steps 1 to 5 to store other stations. y English Notes · A new setting can be stored in place of the former one. · The reception mode (stereo or monaural) is stored along with the station frequency. You can select the preset station number with the numeric buttons (1 to 8) on the remote control if code number "0023" has been set in the AMP/TUN (or DSP/TUN) position. 29 TUNING Exchanging Preset Stations You can exchange the assignment of two preset stations with each other. s Example: If you want to exchange preset station "E1" with "A5" 2, 4 ­ + ­ + L R 1 2 Recall preset station "E1". Refer to the procedure in the section "To Recall a Preset Station" on page 29. Hold down (PRESET/TUNING) EDIT for about three second. "E1" and the "MEMORY" indicator flash. Flashes 3 Recall preset station "A5" by using the buttons on the front panel. "A5" and the "MEMORY" indicator flash. Flashes 4 Press (PRESET/TUNING) EDIT again. The display shows the exchange of stations has been completed. 30 RECORDING A SOURCE ON TAPE, MD OR VIDEO CASSETTE Recording adjustments and other operations are performed from the tape deck, MD recorder or VCR. Refer to the instructions for these components. y If a tape deck or MD recorder is being used for recording, you can monitor the sounds being recorded by pressing TAPE/MD MON / EXT. DECODER (or TAPE/MD). INTRODUCTION 2 1, 4 Notes · The DSP program and the setting of VOLUME, BASS, TREBLE and BALANCE have no effect on the material being recorded. · Composite video and S video signals pass independently through this unit's video circuits. Therefore, when recording or dubbing video signals, if your video source component is connected to provide only an S video (or only a composite video) signal, you can record only an S video (or only a composite video) signal by your VCR. · A source connected to this unit only through the digital terminals cannot be recorded by the tape deck, MD recorder or VCR connected to this unit. · A source connected to the EXTERNAL DECODER INPUT terminals of this unit cannot be recorded. · Check the copyright laws in your country to record from records, CDs, radio, etc. Recording of copyrighted material may infringe copyright laws. ­ + ­ + L R PREPARATION 2 4 If you play back a video source that uses scrambled or encoded signals to prevent it from being dubbed, the picture itself may be disturbed due to those signals. BASIC OPERATION 1 Set VOLUME to the "m" position. Front panel ADVANCED OPERATION 2 Select the source you want to record. or Front panel Remote control 3 4 Begin recording by the tape deck, MD recorder or VCR connected to this unit. Play the source and then turn up the volume to confirm the input source. APPENDIX or Front panel Remote control English 31 ADVANCED OPERATION SOUND FIELD PROGRAM This unit incorporates a sophisticated, multi-program digital sound field processor (DSP). This processor allows you to electronically expand and change the shape of the audio sound field from both audio and video sources, creating a theaterlike experience in your listening room. You can create outstanding audio sound by selecting a suitable DSP program (this will, of course, depend on what you are listening to). When you select a CINEMA DSP program, one of the built-in decoders (Dolby Pro Logic, Dolby Digital and DTS) is turned on according to which type of signals the source being played contains. The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in mind that most of these are precise digital re-creations of actual acoustic environments. [. . . ] 36, 37 Speaker balance (test tone) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 STANDBY/ON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 E External decoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]