User manual YAMAHA RX-V992

[. . . ] RX-V992 NATURAL SOUND AV RECEIVER RX­V992 CINEMA DSP DIGITAL/ PRO LOGIC ENHANCED MOVIE THEATER TV SPORTS STADIUM EFFECT DISCO ROCK CONCERT JAZZ CLUB CHURCH CONCERT HALL VOLUME l6 VCR 2 VCR 1 DVD/ LD 28 20 l2 8 POWER VIDEO AUX TAPE (MD) TV/DBS 40 4 TUNER PHONO CD 60 2 A/ C/ E B/ D/ 1 2 3 4 5 6 7 8 0 ­dB PHONES SPEAKERS A B BASS EXTENSION TONE BYPASS BASS TREBLE BALANCE REC OUT/ ROOM 2 SELECTOR DVD/LD SOURCE TAPE (MD) TUNER CD PHONO FM/AM DOWN TUNING UP DELAY/CENTER /REAR/SWFR SET MENU VIDEO AUX S VIDEO VIDEO L AUDIO R l 2 3 ON OFF 0 l 2 3 4 2 3 4 l 0 l 2 3 4 2 3 4 l 0 l 2 3 4 5R TV/DBS VCR 1 VCR 2 VIDEO AUX MEMORY EDIT TUNING MODE 4 5 5 MAN'L/AUTO FM AUTO/MAN'L MONO 5 5 L5 Natural Sound AV Receiver Récepteur audiovisuel "Son Naturel" OWNER'S MANUAL MODE D'EMPLOI SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN 1 Read Instructions ­ All the safety and operating instructions should be read before the unit is operated. 2 Retain Instructions ­ The safety and operating instructions should be retained for future reference. 3 Heed Warnings ­ All warnings on the unit and in the operating instructions should be adhered to. 4 Follow Instructions ­ All operating and other instructions should be followed. [. . . ] (See page 44 for details. ) In this mode, input signal is automatically selected by the following order of priority. Digital input signal from the COAXIAL jack 2. Analog input signal ANALOG: In this mode, only analog input signal is selected even though digital signal is input at the same time. Select this mode when you want to use the analog input signal instead of the digital input signal. NOTE: For the TV/DBS source only, the input mode selected on the function "8. INPUT MODE" in the SET MENU mode is selected when you turn on the power of this unit. 46 Notes on input mode selection · To play back a source with the Dolby Digital (AC-3) decoded, set the input mode to "AUTO". · When you want to enjoy a source which has normal 2-channel signals with a Dolby Pro Logic Surround program, select the ANALOG mode. In the AUTO mode, there may be a case depending on some LD players or DVD players that when you make a search on a source encoded with the Dolby Digital (AC-3) during the play and then the play is restored, sound output is interrupted for a moment because the digital input signal is selected again. RECORDING A SOURCE TO AUDIO/VIDEO TAPE (OR DUBBING FROM A TAPE TO ANOTHER) NOTE: If you will use the remote control unit, be sure to use it with the lid open. Set the REC OUT selector to the SOURCE position. Front panel REC OUT/ ROOM 2 SELECTOR DVD/LD TV/DBS VCR 1 VCR 2 VIDEO AUX SOURCE TAPE (MD) TUNER CD PHONO English · 2. Select the source you want to record. Front panel VCR 1 DVD/LD DVD/LD Remote control or TAPE (MD) TV/DBS 3. Play the source and increase the setting of the master VOLUME control to confirm it. (For detailed information on tuning operations, refer to page 49. ) Front panel VOLUME l6 20 l2 Remote control MASTER VOLUME 28 8 40 4 or MUTE 60 2 0 ­dB 4. Set the tape deck, MD recorder or VCR used for recording to the recording mode. 47 Regardless of the setting of input selector buttons, when you set the REC OUT selector to a position other than "SOURCE", the source selected by the REC OUT selector can be recorded by other tape deck (MD recorder) and/or VCRs connected to this unit. While recording a source by setting the REC OUT selector to the position other than SOURCE as described above, the following operations can be made at the same time. q NOTE: Adjusting the master VOLUME, BASS, TREBLE controls, etc. , or selecting a sound field program has no effect on the material being recorded. NOTE: Composite video and S video signals pass independently through this unit's video circuits. Therefore, when recording or dubbing video signals, if your video source unit is connected to provide only a S video (or only a composite video) signal, you can record only a S video (or only a composite video) signal on your VCR. NOTE: A source that is connected to this unit between digital jacks only cannot be recorded by a tape deck or VCR connected to this unit. NOTE: Please check the copyright laws in your country to record from records, compact discs, radio, etc. Recording of copyright material may infringe copyright laws. You can monitor the audio (or the audio and video) signals being recorded by selecting the recording unit (TAPE (MD), VCR 1 or VCR 2) with the corresponding input selector button. You can watch or listen to any other source by selecting it with the corresponding input selector button. q If you watch a video software that uses scramble or encoded signals to prevent it from being dubbed, there may be a case that display information superimposed on the picture and/or the picture itself is disturbed due to those signals. 48 TUNING OPERATIONS Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is possible. However, if signals of the station you want to select are weak, you must tune to it manually (MANUAL TUNING). English AUTOMATIC TUNING 1. Select "TUNER" as the input source. Front panel TUNER PHONO MANUAL TUNING 1. [. . . ] 50 dB Image Response Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 dB Spurious Response Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 dB Harmonic Distortion (1 kHz). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . and Canada models] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]