User manual YAMAHA S30

[. . . ] MUSIC SYNTHESIZER OWNER'S MANUAL SPECIAL MESSAGE SECTION This product utilizes batteries or an external power supply (adapter). DO NOT connect this product to any power supply or adapter other than one described in the manual, on the name plate, or specifically recommended by Yamaha. WARNING: Do not place this product in a position where anyone could walk on, trip over , or roll anything over power or connecting cords of any kind. The use of an extension cord is not recommended! [. . . ] You can then use the Reso (Resonance) parameter to add further character to the sound. Six types of LPF are available. Level -6db/oct -12db/oct -18db/oct -24db/oct Resonance LPF6 (Low Pass Filter 6dB/oct) A 1-pole (-6db/oct) dynamic LPF with no Resonance, designed to be used in combination with an HPF (High Pass Filter). Cutoff Frequency 78 · HPF (High Pass Filter) This only passes signals above the Cutoff frequency. You can then use the Reso (Resonance) parameter to add further character to the sound. Two types of HPF are available. Level BPF6 (Band Pass Filter 6dB/oct) The combination of a -6dB/oct HPF and LPF. Level Cutoff range Range passed Cutoff range -6db/oct Frequency -12db/oct -24db/oct Cutoff Frequency BPF12D (Band Pass Filter 12dB/oct Digital) The combination of a -12dB/oct HPF and LPF. Level Cutoff Range Range passed Cutoff Range HPF24D (High Pass Filter 24dB/oct Digital), A 4-pole (-24db/oct) dynamic HPF with a strong Resonance. -12db/oct Frequency Resonance BPFW (Band Pass Filter Wide) Also the combination of a ­12dB/oct HPF and LPF, but can have a wider frequency band than the BPF12D filter. Level Cutoff range Range passed Cutoff range width can be increased HPF12(High Pass Filter 12dB/oct), A 2-pole (-12db/oct) dynamic HPF. Frequency Resonance · BEF (Band Elimination Filter) This attenuates a band of signals around the Cutoff frequency, but passes everything else. BEF6 (Band Elimination Filter 6dB/oct) Level Range passed Cutoff range Range passed · BPF (Band Pass Filter) This only passes a band of signals around the Cutoff frequency. Three types of BPF are available. Center frequency Level Cutoff range Range passed Cutoff range Frequency · THRU The filters are bypassed and the entire signal is unaffected. Center frequency Frequency s Gain Set the Gain (the amount of boost applied to the signal sent to the Filter Unit). Settings: 0 ~ 255 79 Voice Mode s Cutoff Set the Cutoff frequency. This is used as the basic frequency for the selected Filter Type. Settings: 0 ~ 255 FLT Sens (Filter Sensitivity) You can set Filter Sensitivity parameters for each Element. FLTíSens)EGDepth EL1234 +63 VelCutoff VelReso +7 +7 s Reso (Resonance)/Band/Width This parameter's function varies according to the selected Filter Type. If an LPF or HPF has been selected, this parameter is used to set the Resonance. For the BPF (excluding the BPFW) and the BEF, it is used to select the Band. For the BPFW, it is used to adjust the Width of the band. With the LPF and HPF, the Reso parameter is used to set the amount of Resonance (harmonic emphasis) applied to the signal at the Cutoff frequency. This can be used in combination with the Cutoff frequency parameter to add further character to the sound. With the BPF, the Band parameter is used to set the range (band) of signal frequencies passed by the filter. With the BEF, it is used to set the band of signal frequencies attenuated by the filter. In both cases, the Cutoff frequency is the center frequency of the band. With the BPFW, the Width parameter is used to adjust the width of the band of signal frequencies passed by the filter. Settings: 0 ~ 31 Voice Mode s EGDepth Set the sensitivity of the Filter to note velocity. A positive setting will produce large filter changes for notes played harder, and a setting of zero will produce no filter changes at all. With a negative setting, the EG envelope will be inverted. Settings: -64 ~ 0 ~ +63 s VelCutoff (Velocity Cutoff) Set the sensitivity of the Cutoff frequency to note velocity. A positive setting will raise the Cutoff frequency for notes played harder, and lower it for notes played more softly. A negative setting will have the opposite effect. Settings: -64 ~ 0 ~ +63 s VelReso (Velocity Resonance) Set the sensitivity of the selected Resonance parameter to note velocity. A positive setting will produce large Resonance changes for notes played harder, and smaller changes for notes played more softly. A negative setting will have the opposite effect. Settings: -64 ~ 0 ~ +63 FLT HPF (High Pass Filter) You can set the Key Follow parameters for the High Pass Filter. This screen is available only when you have one of the "LPF+HPF" settings for the Type parameter in the Filter Type (FLT Type) screen. FLTíHPF) EL1234 Cutoff 255 KeyFlw +200% FEG VelSens (FEG Velocity Sensitivity) You can set parameters controlling the sensitivity of the Filter Envelope Generator (FEG) to note velocity. FEGíVelSens) EL1234 Level +63 Time-Segment +63 attack s Cutoff Set the center frequency of the Key Follow parameter. Settings: 0 ~ 255 s KeyFlw (Key Follow) Set the Key Follow for the HPF Cutoff. [. . . ] : Kanaalweg 18-G, 3526 KL UTRECHT : 030-2828425 ADVARSEL! Lithiumbatteri--Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. VARNING Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. [. . . ]