User manual YAMAHA S80

[. . . ] MUSIC SYNTHESIZER OWNER'S MANUAL SPECIAL MESSAGE SECTION PRODUCT SAFETY MARKINGS: Yamaha electronic products may have either labels similar to the graphics shown below or molded/stamped facsimiles of these graphics on the enclosure. The explanation of these graphics appears on this page. Please observe all cautions indicated on this page and those indicated in the safety instruction section. Battery Notice: This product MAY contain a small non-rechargable battery which (if applicable) is soldered in place. [. . . ] These Offsets are used by the Break Points (BP1/BP2/BP3/BP4). Details about Filter Scaling are given below in the section "Filter Scaling Settings. " Settings: Ofst1 to Ofst4: -128 ~ 0 ~ +127 Filter Scaling Settings By way of example, you could set the Levels (Offsets) and Break Points (BP1 to BP4) as follows. FLTíScale) EL1234 BP1 E1 BP2 B2 Ofst2 + 10 BP3 G4 Ofst3 + 17 BP4 A5 Ofst4 +4 s Center (Center Key) Set the basic note used by the EGTime parameter. When the Center Key note is played, the FEG behaves according to its actual settings. The pitch change characteristics for other notes will vary in proportion to the EGTime settings. Settings: C-2 ~ G8 You can also set this parameter by pressing the respective note on the keyboard while holding down the [SHIFT] key. Positive value Speed of FEG level change Lower range + FLTíScale)Ofst1 EL1234 -4 Higher range Here, the current Cutoff setting is 64. The Offsets are ­4 at BP1 (set to note E1), +10 at BP2 (set to note B2), +17 at BP3 (set to note G4) and +4 at BP4 (set to A5). That is, the Cutoff frequencies at each Break Point are 60, 74, 81 and 68, respectively. For other notes, the Cutoff frequencies will be on the straight line connecting the two adjacent Break Points. The Break Points are automatically arranged in ascending order across the keyboard. For example, BP2 cannot be set to a lower note than that of BP1. The Break Point Levels are Offsets used to increase or decrease the current Cutoff setting at the specified notes. Regardless of the size of these Offsets, the minimum and maximum Cutoff limits (values of 0 and 127, respectively) cannot be exceeded. A note set below the BP1 will become the BP1 Level. A note set above BP4 will become the BP4 Level. -- Basic Pitch Negative value + Speed of FEG level change Lower range Higher range -- Basic Pitch 87 Voice Mode s Cutoff Set the Filter Key Follow ratio (the amount by which the Filter Cutoff varies according to note position) for each Element. A Center Key setting of C3 is used as the basic setting by the Cutoff parameter. A positive setting will lower the Cutoff frequency for lower notes and raise it for higher notes. A negative setting will have the opposite effect. FLT Scale (Filter Scale Break Point) You can set four Filter Scaling Break Points for each Element. Filter Scaling controls the filter cutoff frequency according to the positions of the notes on the keyboard. There are four Break Points used to divide and assign different settings across the keyboard. The Levels (Offsets) at each of Break Point are set in the FLT Scale screen. Element Amplitude You can set Amplitude parameters to affect the output level of each Element. The following seven screens are available. AEG VelSens (AEG Velocity Sensitivity) AEG Time AEG Level AEG Release AMP KeyFlw (AMP Key Follow) AMP Scale (AMP Scale Break Point) AMP Scale (AMP Scale Offset) s Attack (Attack Time) Set the Attack Time. Settings: 0 ~ 127 s Decay1 (Decay 1 Time) Set the Decay 1 Time. Settings: 0 ~ 127 Voice Mode s Decay2 (Decay 2 Time) Set the Decay 2 Time. Settings: 0 ~ 127 AEG Level AEG VelSens (AEG Velocity Sensitivity) You can set the sensitivity of the Amplitude Envelope Generator (AEG) to note velocity. AEGíVelSens) EL1234 Level +7 Time-Segment +63 attack You can set various Level parameters for the Amplitude Envelope Generator (AEG). Combined with the AEG Time and AEG Release settings, these can be used control the change in output level from the moment a note is pressed on the keyboard to the moment it is released. You can set different values for each Element. AEGíLevel) Init EL1234 127 Attack Decay1 Sustain (127) 127 0 s Level Set the sensitivity of the AEG's Level (its effectiveness) to note velocity. A positive setting will cause larger output level changes for notes played harder and smaller changes for notes played more softly. [. . . ] Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti. (lithium caution) NEDERLAND / THE NETHERLANDS · Dit apparaat bevat een lithium batterij voor geheugen back-up. · This apparatus contains a lithium battery for memory back-up. · Raadpleeg uw leverancier over de verwijdering van de batterij op het moment dat u het apparaat ann het einde van de levensduur afdankt of de volgende Yamaha Service Afdeiing: Yamaha Music Nederland Service Afdeiing Kanaalweg 18-G, 3526 KL UTRECHT Tel. [. . . ]