User manual YAMAHA SHS-10

[. . . ] Cable/s supplied with this product MUST be used. Failure to follow instructions could void your FCC authorization to use this product in the USA. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class "B" digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. [. . . ] (If the selected Aux Send is paired, mutes for both Aux Sends recorded. ) -- -- [ON] buttons of paired channels and grouped mutes are recorded together. Faders of paired channels and grouped faders are recorded together. Pair/Group Pan Input Surround Pan Input SURR EQ (F, Q, G, On/Off) Input, Bus Out, Aux Send, Stereo Out EQ Aux Sends 1­8 Level Input AUX Aux Send 1­8 mutes Input AUX ON Use Aux Send or Aux View pages Use SCENE MEMORY section or Scene Memory page Use corresponding library page Use corresponding page Select User Defined Remote Layer, use faders Select User Defined Remote Layer, use [ON] buttons Select User Defined Remote Layer, use Encoders Scene recalls Library recalls Effects parameters (certain parameters) -- EQ, Gate, Comp, Effects, Channel Effects processors 1­4 -- -- -- -- Faders User Defined Remote Layer [ON] buttons Encoders FADER ON PAN -- -- -- DM1000 Version 2--Owner's Manual Punching In & Out 197 Punching In & Out You can modify part of a recorded Automix or add events to an Automix (Punch In & Out). You can punch in and out channels using the [SEL] buttons, or individual parameters using other controls. Punch In & Out Using the [SEL] Buttons Follow the steps below to punch channels in and out using the [SEL] buttons. 1 Select parameters you wish to record in the OVERWRITE section. 2 Move the cursor to the REC or AUTO REC button at the bottom of the page, then press [ENTER]. At this time, make sure that the [SEL] button indicators for all channels (including the channels you want to punch in) are lit green. The REC and PLAY buttons are highlighted and parameter event recording is armed. However, no events are yet recorded since no channels are selected. 5 To punch in channels, press the corresponding [SEL] buttons. The corresponding [SEL] button indicators light up red and the channels are placed in record mode. · Green . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automix stopped or playing · Orange. . . . . . . . . . . . . . . . . . . . . . . . . . . The channel is armed. · Red . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automix recording in progress · Flashing red . . . . . . . . . . . . . . . . . . Edit Out mode set to TAKEOVER, and fader events continue recording after punch out · Flashing green. . . . . . . . . . . . . . Edit Out mode set to TAKEOVER, and faders are disabled after punch out Playing Back an Automix As long as the Automix function is enabled, the Automix function will chase the incoming timecode and play and stop the current Automix accordingly. You can stop playback manually by moving the cursor to the STOP or ABORT button on the Automix | Main/Memory page, then pressing [ENTER]. Playback will stop automatically if the DM1000 receives no timecode for a while, if the DM1000 receives MIDI Stop commands (only when the MIDI CLOCK source is selected), or if the end of the Automix data is reached. While the [AUTO] button indicator is lit, the [SEL] button indicators light up green on the channel strips available for Automix playback. When Automix playback for an individual channel is disabled, its [SEL] button indicator turns off. During playback, faders move in accordance with recorded fader events (as long as the corresponding layer and Fader mode is selected). You can disable fader movement by turning off the MOTOR button on the Fader 1 or 2 page (see page 205). You can view fader events on the Fader 1 or 2 page (see page 205), and other events on the corresponding pages. Recorded events of the currently-selected channel are reflected in the SELECTED CHANNEL section controls and displays. Note: If the current effects type is different from that used when the effects parameter edits were recorded, the parameter edits will not be played back. [. . . ] Input [+24dBu] [+18dBu] CASCADE IN CASCADE OUT Digital Clipping Level Max. Output [+24dBu] +24 +20 +10 +4 0 ­10 ­20 ­30 [+4dBu] Nominal Input GAIN MIN. , PAD ON Nominal Output [+4dBu] [­2dBu] OMNI OUT 1-12 Max. Input [­40dBu] ­40 ­50 Nominal [­60dBu] Input In GAIN MAX. , PAD OFF ­60 ­70 ­80 ­90 ­100 ­110 ­120 ­130 ­140 ­150 ­160 DSP Noise Floor ­170 ­180 ­190 [0dBu = 0. 775Vrms] [0dBFS = Full Scale] For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. [. . . ]