User manual YAMAHA SPM-K30

[. . . ] · Make sure to leave adequate ventilation space around the unit to allow heat generated by the Digital Sound Projector to dissipate. Failure to provide adequate space around the unit could cause the Digital Sound Projector to overheat internally, resulting in a fire. · Never hang from the Digital Sound Projector or the wall bracket. Hanging from the Digital Sound Projector or the wall bracket could cause the Digital Sound Projector or the wall bracket to fall, resulting in personal injury. [. . . ] If the metal apparatuses are not attached to the rear panel of your Digital Sound Projector, proceed to step 3. Metal apparatus Metal apparatus En 5 INSTALLATION PROCEDURE 3 Attach the small wall mount brackets to the Digital Sound Projector. The small wall mount brackets vary depending on the type of the Digital Sound Projector. Refer to the following table for details on the type of the Digital Sound Projector and the compatible small wall mound brackets (Type A or B). Use supplied projector mounting screws (M6 x 4 for YSP-4000, YSP-40D or HTY-7040 and M4 x 8 for other models) to securely attach the two small wall mount brackets to the rear left and right sides of the Digital Sound Projector. YSP-4000/YSP-40D/HTY-7040 Digital Sound Projector YSP-800 YSP-900 YSP-3000 YSP-30D YSP-3050 HTY-7030 YSP-4000 YSP-40D HTY-7040 Small wall mount bracket Type A Projector mounting screws (M6) (supplied) Type B Rear View Digital Sound Projector Attach the brackets to the rear left and right sides of the Digital Sound Projector. YSP-3000/YSP-30D/HTY-7030/ YSP-3050 Rear View Digital Sound Projector YSP-800/YSP-900 Rear View Small wall mount bracket (Type B) Digital Sound Projector Projector mounting screws (M4) (supplied) Projector mounting screws (M4) (supplied) Small wall mount bracket (Type A) Small wall mount bracket (Type B) Notes · In the unit of the model that the metal apparatuses are not attached, there are felt covers in the holes. In this case, tighten the screws to puncture the felt covers. · If you tighten the screws on the slant, the screw threads in the projector might be broken. Be careful when using electric tools. En 6 INSTALLATION PROCEDURE 4 Attach the safety wire. Attach the safety wire to the small wall mount bracket to prevent the Digital Sound Projector from falling. Slip one end through the loop at the other end Slip the safety wire between the bracket and the projector English Safety wire Repeat the same procedure for the other bracket. 5 Mount the Digital Sound Projector on the wall. Fit the mounting guide hooks of the small wall mount brackets attached to the Digital Sound Projector into the holes on the left and right sides of the large wall mount bracket and then slide the unit to the right. Fit the hook into the hole. Slide the unit to the right. Note Hold the Digital Sound Projector tight with both hands when attaching or removing the Digital Sound Projector to or from the wall. Holding the Digital Sound Projector loosely could cause the Digital Sound Projector to fall, resulting in personal injury. En 7 INSTALLATION PROCEDURE 6 Secure the unit. Align the holes in the large wall mount bracket with the holes in the bottom of the small wall mount brackets, and then use two of the supplied projector mounting screws (M6 x 16) to secure the unit. The positions of the screw holes vary depending on the type of the Digital Sound Projector. Refer to the following illustrations and check the correct positions of the screw holes used to secure your Digital Sound Projector. YSP-800/YSP-900 Digital Sound Projector Bottom View Projector mounting screws (M6) (supplied) Use the inward screw hole on each side to secure your Digital Sound Projector. YSP-3000/YSP-30D/YSP-3050/HTY-7030/ YSP-4000/YSP-40D/HTY-7040 Digital Sound Projector Bottom View Projector mounting screws (M6) (supplied) Use the outward screw hole on each side to secure your Digital Sound Projector. En 8 INSTALLATION PROCEDURE 7 Attach the safety wires to the wall. Pass the screws (commercially available) through the loops of the safety wires and then tighten the screws to secure the safety wires to the wall. Make sure that the screws are strong enough to bear the weight of the Digital Sound Projector and the brackets in case they fall. Screw (commercially available) English Secure the safety wire to the wall. Secure the safety wire to the wall. Washer (supplied) Notes · Attach the safety wires tight. · Keep the 2 other washers for future use. Limited Guarantee for European Economic Area (EEA) and Switzerland Thank you for having chosen a Yamaha product. [. . . ] The following are excluded from this guarantee: a. Periodic maintenance and repair or replacement of parts due to normal wear and tear. Damage resulting from: (1) Repairs performed by the customer himself or by an unauthorised third party. (2) Inadequate packaging or mishandling, when the product is in transit from the customer. [. . . ]