User manual YAMAHA SPS-10MM

[. . . ] SPEAKER STAND Read this before use SPS-10MM PRECAUTIONS ASSEMBLY INSTRUCTIONS Thank you for selecting the Yamaha SPS-10MM speaker stand. This speaker stand is only for the speaker systems listed in "USABLE SPEAKERS" below. Do not use the speakers other than these listed. [. . . ] YAMAHA shall not be liable for any accident caused by improper placement or installation of speakers. DIMENSIONS (mm/inch) Top view 80 (3-3/16") 60 (2-3/8") SPECIFICATIONS Dimensions (W x H x D) : 300 x 618 ­ 868 x 300mm (11-13/16" x 24-5/16 ­ 34-3/16" x 11-13/16") Weight : 1. 6 kg (3 lbs. 8 oz. ) 300 (11-13/16") 64 (2-1/2") USABLE SPEAKERS 300 (11-13/16") 618­868 (24-5/16"­34-3/16") Front view NS-10MM NS-10MMT NX-220P (the main and rear speakers included in the NS-P220 speaker package) NS-E104 (the rear speakers included in the NS-P320 speaker package) NS-E114 (the rear speakers included in the NS-P326 speaker package) NX-S100S (the front and rear speakers included in the DVX-S100 sound system) YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE. , BUENA PARK, CALIF. 135 MILNER AVE. , SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G. m. b. H. 22-34, 25462 RELLINGEN BEI HAMBURG, F. R. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A. B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST. , SOUTH MELBOURNE, 3205 VIC. , AUSTRALIA 21 (13/16") 282 (11-1/8") Printed in Japan V816800-1 ASSEMBLY PROCEDURES Before beginning assembly, check the parts list and make sure all the parts are included. ASSEMBLY FIGURE Speaker PARTS LIST PARTS NOS. EP040090 VV249400 EG340360 VV249200 VV249500 VV249300 QUANTITY 12 7 4 8 1 4 NAME 1 + self-binding tapping screws (4 x 12) 2 Hexagon socket set screws 3 + self-binding screws (4 x 8) 4 Pads 5 Wrench (hexagonal) 6 Gaskets Speaker cable ASSEMBLY PROCEDURES (You will need a screwdriver for assembly. ) 6 6 1. Attaching the base and support. Pass the support through the hole from the bottom of the base, and fasten the + self-binding tapping screws 1. Fix the support so that the holes for the screws comes to the rear side. Plate 3 Pole Do not overtighten the + self-binding tapping screws 1. Doing so may damage the screws or assembly. 3 Limit of the stand height Support 2. Attaching the pole and support. 5 2 2 Insert the pole to the support, and fasten the hexagon socket set screws 2 into the three hole on the support using the included wrench 5. The line on the pole shows the limit of the stand height. [. . . ] Wiring the speaker cables. Base Insert the speaker cables to the hole on the plate, and aligned them to the grooved part on the bottom of the base. 4 1 1 6. Attaching the speakers. 4 Line up the holes on the bottom of the speaker and the center hole on the plate, and fasten the + binding screws 3. In order to ensure that the speakers do not fall, always hold the speakers while attaching the speakers. [. . . ]