User manual YAMAHA SPS-30MMSJ

[. . . ] SPS-30MMS 1 2 3 3 5 4 5 6 7 8 . . 8 8 1 80 60 5 4 4 3 3 5 2 2 7 · · 2 7 · 2 2 320 64 6 320 6 6 1 1 618-868 8 278 25 3 5 3 5 4 8 8 5 3 4 · 3 © 2005 All rights reserved. 5 3 4 5 · 2 Printed in China WG59990 SPEAKER STAND Read this before use ASSEMBLY PROCEDURES Before beginning assembly, check the parts list and make sure all the parts are included. SPS-30MMS PRECAUTIONS ASSEMBLY INSTRUCTIONS ASSEMBLY FIGURE For speakers with screw holes at the left and right of the speaker base. Speaker PARTS LIST NAME 1 Binding tapping screw (4 x 14 mm) 2 Hexagon socket set screw 3 Binding machine screw (4 x 12 mm) 4 Washer Use the binding machine screw 3 or 5 Speaker cable QUANTITY 6 3 + 1 spare 2 2 2 4 1 2 Thank you for selecting the Yamaha SPS-30MMS speaker stand. This speaker stand is only for the speaker systems listed in "USABLE SPEAKERS" below. Do not use the speakers other than these listed. [. . . ] ASSEMBLY PROCEDURES (You will need a screwdriver for assembly. ) 8 1. Pass the support through the hole from the bottom of the base, and fasten the binding tapping screws 1. · Fix the support so that the holes for the screws comes to the rear side. · Do not overtighten the binding tapping screws 1. Doing so may damage the screws or assembly. 7 5 3 2 2 Support DIMENSIONS Top view 80 (3-3/16") 60 (2-3/8") unit: mm(inch) USABLE SPEAKERS NS-10MMT (NS-10MMTS) NX-430P (the main and rear speakers included in the NS-P430/ NS-P436 speaker package) NX-S20 (the front and rear speakers included in the AVX-S20 home theater sound system) NS-M125 NS-M225 NX-S30 (the satelite speakers included in the AVX-S30 home theater sound system) Limit of the stand height 2. Insert the pole to the support, and fasten the hexagon socket set screws 2 into the three holes on the support using the included wrench 7. · The line on the pole shows the limit of the stand height. Do not use the stand pulling out the pole above from this line. The hexagon socket set screw 2 of the lower side becomes ineffective and the fixation becomes unstable. 320 (12-5/8") 64 (2-1/2") Base 6 6 3. Put the pads 6 to the four corners on the bottom of the base to prevent the stand from moving rickety. Put the gaskets 8 to the both sides of the plate. Insert the speaker cables to the hole on the plate, and pass through the pole. Aligned them to the grooved part on the bottom of the base. Line up the holes on the bottom of the speaker and the center holes on the both sides of the plate. Depending on the speakers, choose either the binding machine screws 3 (4 x 12mm) or the binding machine screws 5 (6 x 14mm) to fasten them into the holes. If the speaker has 4mm holes on the bottom: 320 (12-5/8") 1 618-868 (24-5/16"-34-3/16") Front view 1 For speakers with screw holes at the front and rear of the speaker base. Speaker 278 (11") 25 (1") Use the binding machine screw 3 or 5 SPECIFICATIONS Speaker cable Dimensions (W x H x D) : 320 x 618 ­ 868 x 320 mm (12-5/8" x 2 -5/16" ­ 34-3/16" x 12-5/8") : 2. 4 kg (5 lbs. [. . . ] YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND SCANDINAVIA A. B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST. , SOUTH MELBOURNE, 3205 VIC. , AUSTRALIA 4 5 Printed in China WG59990 3 5 3 4 [. . . ]