User manual YAMAHA SPX90

[. . . ] · Do not place the power cord near heat sources such as heaters or radiators, and do not excessively bend or otherwise damage the cord, place heavy objects on it, or place it in a position where anyone could walk on, trip over, or roll anything over it. Water warning · Do not expose the device to rain, use it near water or in damp or wet conditions, or place containers on it containing liquids which might spill into any openings. · Never insert or remove an electric plug with wet hands. If you notice any abnormality · If the power cord or plug becomes frayed or damaged, or if there is a sudden loss of sound during use of the device, or if any unusual smells or smoke should appear to be caused by it, immediately turn off the power switch, disconnect the electric plug from the outlet, and have the device inspected by qualified Yamaha service personnel. · If this device should be dropped or damaged, immediately turn off the power switch, disconnect the electric plug from the outlet, and have the device inspected by qualified Yamaha service personnel. Do not open · Do not open the device or attempt to disassemble the internal parts or modify them in any way. The device contains no user-serviceable parts. [. . . ] Higher settings of this parameter will make the filter return more slowly. *a. The range of this parameter depends on the sampling frequency at which the SPX90 is operating. Effect list The following tables show the default parameter values for the effect belonging to the Dynamic Filter type (PRESET bank). 78 Effect name DYNA FILTER SOURCE INPUT SENSE 48 TYPE BPF OFFSET 4 RESO. The default value of this parameter depends on the sampling frequency at which the SPX90 is operating. The value shown in the table is for fs = 96 kHz. 58 SPX90--Owner's Manual Dynamic Flanger (PRESET bank) This effect uses the input signal or MIDI messages to vary the delay time of the effect sound, creating modulation in a specific frequency region. Each aspect of the sound is controlled by the following effect parameters. Modulation signal: SOURCE Effect sound: SENSE, OFFSET, FB. GAIN Filter/equalizer: LSH G, LSH F, EQ G, EQ F, EQ Q, HSH G, HSH F Output level: OUT LVL, MIX BAL. Parameter details Basic parameters Parameter name SOURCE Range INPUT, MIDI Explanation SENSE OFFSET FB. GAIN 0--100 0--100 ­99%--+99% Source of the modulating signal. If you select INPUT, the effect sound will change according to the input signal. If you select MIDI, the modulated sound will change according to the received MIDI messages (velocity). If you want the effect to vary according to your keyboard performance, select MIDI. Higher settings of this value will cause the delay time to follow the SOURCE more faithfully. 76 Effect name DYNA FLANGE SOURCE INPUT SENSE 85 OFFSET 48 FB. 100% HSH G 0. 0 dB OUT LVL 100% HSH F 10. 0 kHz DIR. UP DECAY*a 158 ms LSH G 0. 0 dB LSH F 125 Hz EQ G 0. 0 dB EQ F 1. 00 kHz EQ Q 2. 0 *a. The default value of this parameter depends on the sampling frequency at which the SPX90 is operating. The value shown in the table is for fs = 96 kHz. SPX90--Owner's Manual 59 Modulation Balance between the original sound and effect sound. At a setting of 0% only the original sound will be output; at a setting of 100% only the effect sound will be output. Output level after the original sound and effect sound have been mixed. Decrease this value if you want to lower the output. At a setting of 0% there will be no output. Direction in which the delay time will move in response to the SOURCE signal. Dynamic Phaser (PRESET bank) This effect uses the input signal or MIDI messages to vary the phase-shifted frequency, creating modulation in a specific frequency region. Each aspect of the sound is controlled by the following effect parameters. [. . . ] :Tune :Clock :Commands :All Sound Off :Reset All Cntrls :Local ON/OFF :All Notes OFF :Active Sense :Reset O*2 X X X O X X X X X O O Common System Real Time *4 Aux Messages Notes receive if switch is on. transmit/receive if exclusive switch is on. Bulk Dump/Request, Parameter Change/Request Effect Control(Depend On Program) O: Yes X: No Mode 1: OMNI ON, POLY Mode 3: OMNI OFF, POLY Mode 2: OMNI ON, MONO Mode 4: OMNI OFF, MONO For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. [. . . ]