User manual YAMAHA STAGEPAS150M

[. . . ] EN Troubleshooting Owner 's Manual Power does not turn on · Is the included power cord correctly connected to a power outlet? CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Explanation of Graphical Symbols The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. Dimentions Speaker Mixer 160 Unit: mm CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Introduction Power shuts down suddenly Thank you for your purchase of the Yamaha PORTABLE PA SYSTEM STAGEPAS 150M. The STAGEPAS 150M is a versatile, compact PA system consisting of a speaker and a mixer. In order to get the most out of your new STAGEPAS 150M and its sophisticated functions, we suggest you read through this manual thoroughly. [. . . ] · The company names and product names in this manual are the trademarks or registered trademarks of their respective companies. IMPORTANT Please record the serial number of this unit in the space below. Model: Serial No. : The serial number is located on the bottom or rear of the unit. Retain this Owner's Manual in a safe place for future reference. · This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (Ser. No) Getting a more powerful sound from the speakers · Is the SPEECH/MUSIC switch set to MUSIC ( )? As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire which is coloured GREEN-and-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or colored GREEN or GREENand-YELLOW. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. (3 wires) · Are the Equalizer controls (HIGH/LOW) set to appropriate levels?Location For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Getting a clearer sound for announcements · Is the SPEECH/MUSIC switch set to SPEECH ( Use only the mixer's handles when removing the mixer from the speaker and when carrying the mixer Caution NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 POLAND Yamaha Music Central Europe GmbH Sp. z. 17 Stycznia 56, PL-02-146 Warszawa, Poland Tel: 022-868-07-57 ASIA THE PEOPLE'S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co. , Ltd. 25/F. , United Plaza, 1468 Nanjing Road (West), Jingan, Shanghai, China Tel: 021-6247-2211 · Before moving the device, remove all connected cables. · When setting up the device, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. Even when the power switch is turned off, electricity is still flowing to the product at the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet. · Do not use the device in a confined, poorly-ventilated location. Make sure that there is adequate space between the mixer and surrounding walls or other devices: at least 30 cm at the sides, 30 cm behind and 30 cm above. If the mixer is to be used installed into the speaker cabinet, make sure to allow adequate space between the speaker and the surrounding walls or other devices: at least 30 cm at the sides, 30 cm behind and 30 cm above. Inadequate ventilation can result in overheating, possibly causing damage to the device(s), or even fire. · Do not use the speaker's handles for suspended installation. Doing so can result in damage or injury. · Avoid setting all equalizer controls and faders to their maximum. Depending on the condition of the connected devices, doing so may cause feedback and may damage the speakers. [. . . ] MIC/LINE switch Set this switch to MIC or LINE for channels 1, 2, depending on the level of the input signal. For low-level signals (such as that of microphones), set the switch to the MIC ( ) position. For high-level signals (such ) position. as keyboard instruments and audio equipment), set the switch to the LINE ( L R L R L R L R L R For low-level signals (such as that of microphones), set the switch to the MIC ( ) position. [. . . ]