User manual YAMAHA TDM900-2002

[. . . ] OWNER'S MANUAL TDM900 5PS-28199-E0 EAU03338 INTRODUCTION Welcome to the Yamaha world of motorcycling!As the owner of a TDM900, you are benefiting from Yamaha's vast experience and newest technology regarding the design and manufacture of high-quality products, which have earned Yamaha a reputation for dependability. Please take the time to read this manual thoroughly, so as to enjoy all advantages of your TDM900. The owner's manual does not only instruct you in how to operate, inspect and maintain your motorcycle, but also in how to safeguard yourself and others from trouble and injury. [. . . ] Place the motorcycle on a level surface and let the engine cool if necessary. (See page 3-11 for seat removal and installation procedures. ) 3. (See pages 6-5 and 6-6 for cowling and panel removal and installation procedures. ) 4. Remove the fuel tank bolts, and then lift the fuel tank to position it away from the coolant reservoir. Place a container under the engine to collect the used coolant. _ WARNING Never attempt to remove the radiator cap when the engine is hot. _ _ 6-13 PERIODIC MAINTENANCE AND MINOR REPAIR 1. Remove the radiator cap retaining bolt and the radiator cap. EW000067 7. Remove the coolant drain bolts to drain the cooling system. 1. Coolant reservoir WARNING Never attempt to remove the radiator cap when the engine is hot. _ _ 8. Pull the coolant reservoir upward and away from the motorcycle. Drain the remaining coolant from the coolant reservoir by opening the cap, then turning the reservoir upside down. Install the coolant reservoir by placing it in the original position, and then installing the bolt. After the coolant is completely drained, thoroughly flush the cooling system with clean tap water. 6 6-14 PERIODIC MAINTENANCE AND MINOR REPAIR 13. Install the coolant drain bolts, and then tighten them to the specified torque. NOTE: Check the washers for damage and replace them if necessary. _ _ Tightening torque: Coolant drain bolt: 7 Nm (0. 7 m·kgf) 14. Pour the recommended coolant into the radiator until it is full. 6 _ Antifreeze/water mixture ratio: 1:1 Recommended antifreeze: High-quality ethylene glycol antifreeze containing corrosion inhibitors for aluminum engines Coolant quantity: Total amount: 1. 7 L Coolant reservoir capacity: 0. 3 L EC000080 G If water has been added to the coolant, have a Yamaha dealer check the antifreeze content of the coolant as soon as possible, otherwise the effectiveness of the coolant will be reduced. _ CAUTION: G If coolant is not available, use distilled water or soft tap water instead. Do not use hard water or salt water since it is harmful to the engine. G If water has been used instead of coolant, replace it with coolant as soon as possible, otherwise the engine may not be sufficiently cooled and the cooling system will not be protected against frost and corrosion. 6-15 15. Install the radiator cap, start the engine, let it idle for several minutes, and then turn it off. Remove the radiator cap to check the coolant level in the radiator. If necessary, add sufficient coolant until it reaches the top of the radiator, and then install the radiator cap and the cap retaining bolt. Check the coolant level in the reservoir. [. . . ] 6-31 Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4 Storage compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11 Supporting the motorcycle . . . . . . . . . . . . . . . . . . . . . 6-37 Wheel (rear) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]