User manual YAMAHA TP65

[. . . ] Inside This Package Before setup, please make sure that all of the items listed below are present and accounted for. If anything is missing, please contact the dealer from whom you purchased the unit. OWNER'S MANUAL * To customers who purchased a pads set (DTPK95M, DTPK95MSP etc. ), please refer to the attached "Accessories List" sheet included with each pads set when confirming package contents. TP65 TP65S · TP65S (Main Unit, Clamp Bolt) x1 INTRODUCTION Thank you for purchasing the TP65/65S Yamaha Drum Pad. [. . . ] Do not use benzine, thinner or alcohol as it may result in discoloration or deformation. Also pay close attention so as not to let the water and detergent come into contact with the cushions used in the product, it may result in deterioration. · When connecting or disconnecting the cable, make sure that you hold the plug, not the cable. Also, never place any heavy objects on the cable and never allow any sharp objects to come into contact with the cable. Applying excessive force to the cable may result in damage to the cable such as cutting the wires, etc. Plug has two black rings (The monaural type connector has one black ring. ) Replacing Worn Pads · After extended use, some of the parts used on the PCY65/65S will wear out or their quality will deteriorate (pad rubber, connecting jacks, etc. ). The life of these parts will vary depending upon the circumstances under which the PCY65/65S is used. · Please ask the dealer from whom you purchased the device about replacing worm parts. Troubleshooting If you experience any of the following problems while using the TP65/65S, please check the information provided below before contacting your dealer. No sound, low Volume Problem Is the TP65/65S properly connected to the DTX Series Drum Trigger Module's input jack using the supplied stereo phone cable?Is the module properly connected to a pair of headphones or an external audio device such as an amplifier, speakers, etc. ?Are module settings correct? What to check Refer to the previous "Connections" section and check whether the connections are proper or not. Check the connections between the drum trigger module and the external device or headphones, also check the external device's power switch or volume settings. Check the volume setting of the voice assigned to the input jack to which the TP65/65S is connected (refer to the previous "Adjusting the Voice Volume" section), or whether or not the headphone volume is set too low, etc. Also refer to the Owner's Manual that came with your drum trigger module (DTXPRESS/DTX/DTXTREME) regarding the problems described above or any other problems you may experience. If a solution to the problem can not be found even after consulting the manuals, contact the dealer from whom you purchased the product. Part Names TP65 Pad Connections Use the supplied stereo phone cable to connect the pad's output jack with the input jack TP65S Pad Output jack Clamp Bolt (SNARE, TOM 1, etc. ) on the drum trigger module (DTXPRESS/DTX/DTXTREME). Connect the cable's L-shaped plug to the TP65/65S. Output jack Insert The manner in which the TP65/65S will function corresponds to the INPUT numbers on the Right Rim (The TP65S contains switches in its left and right rim sections. ) Left Rim DTX Series Drum Trigger Module shown in the chart below. Connect to the input that is used for the tom pad on your drum trigger module. (Refer to the Owner's Manual that came with the drum trigger module for further information. ) A single voice is assigned to, and produced by the pad. Setting Up After setting up your rack system (Yamaha RS70, etc. ) or a standard tom stand (Yamaha WS series, etc. ), attach the TP65/65S as shown in the diagram below. Insert the tom holder (hexagonal bar) on your rack or tom stand into the pad, and firmly tighten the clamp bolt to secure. Individual voices can be assigned to, and produced by the pad and rim (2 voices). Individual voices can be assigned to, and produced by the pad, left rim, and right rim (3 voices). Individual voices can be assigned to, and produced by the pad, and right rim (2 voices: the left rim switch is inactive). Tom Holder Insert Make sure that a stereo cable is used when connecting the TP65S to the module. If a monaural cable (Plug has one black rings) is used, the voices set to the right/left rim will not be produced. Clamp Bolt Adjusting the Voice Volume To change the volume of the voice(s) assigned to the TP65/65S, use the [VOICE] Edit Mode in the DTX Series Drum Trigger Module. [. . . ] The model number, serial number are located on this plate. You should record the model number, serial number, and the date of purchase in the spaces provided below and retain this manual as a permanent record of your purchase. Model : TP65 Model : TP65S Purchase Date Serial No. Serial No. PLEASE KEEP THIS MANUAL Printed in Indonesia WF75880 [. . . ]