User manual YAMAHA TSS-1

[. . . ] UCA HOME THEATER SOUND SYSTEM SYSTEME AUDIO HOME CINEMA TSS-1 Active Servo Technology OWNER'S MANUAL MODE D'EMPLOI DIGITAL 4CH 2CH DTS DIGITAL PROLOGIC INPUT MODE TEST MUTE CENTER SURROUND SUBWOOFER MASTER VOLUME Active Servo Technology HOME THEATER SOUND SYSTEM TSS-1 · Explanation of Graphical Symbols CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. IMPORTANT Please record the serial number of this system in the space below. Model: Serial No. : The serial number is located on the rear of the main unit. [. . . ] The surround speakers are used for effect sounds, and the center speaker is for center channel sound (dialog etc. ). The subwoofer is used for reproducing sounds of low frequencies from the front, center and surround channels. The subwoofer also reproduces sounds of the subwoofer channel when a DTS or Dolby Digital encoded source is played. Surround speakers: Behind your listening position or on both sides of the listening room. Center speaker: Precisely between the front speakers. * The center speaker can be mounted on the monitor as shown on the next page. The position of the subwoofer is not so critical because low bass tones are not highly directional. Subwoofer: Left front speaker Right front speaker Center speaker Right surround speaker Amplifier unit Subwoofer Left surround speaker E-4 English Adjusting the front angle of the satellite speakers The front angle of the satellite speakers can be adjusted as shown below. Placing a center speaker on top of the monitor When placing the center speaker on top of the monitor, remove the stand from the speaker, and attach the provided fastener at the bottom of the speaker and on top of the monitor to prevent the speaker from falling. * Do not place the speaker on top of the monitor with an inclination of more than 10 degrees. 1 Loosen the screw on the bottom of the speaker stand. * Attach the supplied nonskid pads at the four corners on the bottom of the stand for improved stability. 10 10 Pads Fastener 2 Adjust the speaker angle on the stand as you prefer, and then tighten the screw. Note Though this speaker is a magnetically shielded type, there may be some influence on the monitor picture depending on the type of monitor or the placement of the speaker. In such a case, place the speaker further apart from the monitor until there is no influence on the monitor picture. Mounting satellite speakers on a wall The satellite speakers can also be hung on the wall. Fasten screws into a firm wall or wall support as shown in the figure, and hang the slits on the rear of the speaker on the protruding screws. * Make sure that the screws are securely caught by the slits. Tapping screw (4 mm) (Available in hardware stores) Mounting the amplifier unit on the supplied stand For improved stability, it is recommended to mount the amplifier unit on the supplied stand with the supplied screws as shown below. * Attach the supplied nonskid pads at the four corners on the bottom of the stand for improved stability. 4 mm Min. 20 mm 50 mm Wall/ wall support To front Pads Warning Each speaker weighs 0. 4 kg (0. 9 lbs. ). Do not mount them on thin plywood or a wall with soft surface material. If mounted, the screws may come out of the flimsy surface and the speakers may fall. This could damage the speakers and cause personal injury. Do not install the speakers on a wall with nails, adhesives, or any other unstable hardware. Long-term use and vibrations may cause them to fall. To avoid accidents resulting from tripping over loose speaker cords, fix them to the wall. E-5 Connections (See figure 1 on page IV. ) Caution: Plug in the amplifier unit and other equipment after all connections are completed. A : Connect the three satellite speakers with a 3 m cord to the FRONT L, R and CENTER terminals. Connect the two satellite speakers with a 7 m cord to the SURROUND L and R terminals. Connect the subwoofer to the SUBWOOFER terminal. B : Connect external audio/video units (a personal computer, a video game player, a portable DVD/CD player, a video cassette player, etc. [. . . ] Noise. The level of the input signal is too high. The level of the input signal is too low. The amplifier unit is too close to the monitor. E-9 Specifications Amplifier unit Output Power per Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Satellite: 6W (1 kHz, 4, 10% THD) Subwoofer: 18W (100 Hz, 4, 10% THD) Input Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]