User manual YAMAHA TSS-101

[. . . ] UB HOME THEATER SOUND SYSTEM TSS-10 INPUT DIGITAL 1 DIGITAL 2 ANALOG MODE DTS DIGITAL PL MOVIE PL MUSIC VOLUME TRIM 7 +6 6 +4 5 +2 4 0 3 ­2 2 ­4 1 ­6 INPUT MODE REAR S. WOOFER VOLUME MUTE TEST Active Servo Technology SILENT STANDBY/ON TSS-10 HOME THEATER SOUND SYSTEM OWNER'S MANUAL CAUTION: READ THIS BEFORE OPERATING YOUR SYSTEM. 1 2 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. Install this sound system in a well ventilated, cool, dry, clean place with at least 20 cm on the top, 10 cm on the left and right, and 10 cm at the back of the amplifier unit -- away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. Locate this system away from other electrical appliances, motors, or transformers to avoid humming sounds. [. . . ] · Do not connect the included AC adaptor to any unit other than the amplifier unit of this system. ANALOG INPUTS DC IN 15V +4 5 +2 4 0 3 ­2 2 ­4 1 ­6 SILENT STANDBY/ON AC adaptor (included) Power cable (U. S. A. model) (included) To AC outlet 10 ADJUSTING SPEAKER OUTPUT LEVELS This section explains how to adjust speaker output levels using the test tone generator. When this adjustment is complete, the output level heard at the listening position should be the same from each speaker. This is important for best performance of the various decoders (Dolby Digital, Dolby Pro Logic II and DTS). Left front Right front PREPARATION Center Note · Since this system cannot enter the test mode while headphones are connected to the amplifier unit, be sure to unplug the headphones from the SILENT jack when using the test tone. Left rear Right rear Using the test tone 3 Use the test tone to balance the output levels of the speakers. Adjust the level of each speaker by pressing VOLUME +/­ so that it matches the level of the front speakers. While adjusting, the test tone is heard from the selected speakers. After ­ or + is released, the test tone begins travelling to another speaker again. Notes · The adjustment of each speaker output level should be made at your listening position using the remote control. · The test tone may not be heard if the volume level of this system is too low. Confirm that the volume is set to a proper listening level. 4 When adjustment is complete, press TEST to stop the test tone. · While adjusting, the level of the selected speaker is shown by the lighting of the VOLUME indicators on the front panel. The default level is also shown by the dim lighting of the corresponding indicator. INPUT MODE REAR S. WOOFER y VOLUME +/­ TEST VOLUME MUTE TEST · You can enjoy listening to the input source at the desired volume simply by turning VOLUME on the front panel or pressing VOLUME +/­ on the remote control. Notes · If you press INPUT on the remote control when the test tone is outputted, the output levels of all channels are reset to the default levels. · The levels of the left and right front speakers cannot be set over the point on the VOLUME indicator shown in the figure below. PL MOVIE PL MUSIC INPUT DIGITAL 1 DIGITAL 2 ANALOG VOLUME TRIM DTS DIGITAL MODE 7 +6 6 +4 5 PL MOVIE PL MUSIC VOLUME TRIM 7 +6 6 +4 5 +2 1 2 Press to turn on the power. +2 4 0 3 ­2 2 ­4 1 ­6 4 0 3 ­2 2 ­4 1 ­6 Press TEST to output the test tone. The test tone is heard (in order) from the left front, center, right front, right rear and left rear speaker. The tone is produced for about 2. 5 seconds from each speaker. · All of the INPUT indicators flash while the test tone is being outputted. SILENT STANDBY/ON English 11 PLAYING A SOURCE Let's listen to sources played on the audio and video components connected to this system. I To adjust the subwoofer level While listening to a source, press S. WOOFER ­ or +. Pressing + increases and ­ decreases the level. Front panel Remote control y INPUT INPUT DIGITAL 1 DIGITAL 2 ANALOG INPUT INPUT MODE · While adjusting, the current level is shown by the lighting of the VOLUME indicators on the front panel. The default level is also shown by the dim lighting of the corresponding indicator. MODE DTS DIGITAL PL MOVIE PL MUSIC REAR Note REAR +/­ S. WOOFER +/­ S. WOOFER VOLUME TRIM 7 +6 6 +4 5 +2 4 0 3 ­2 2 ­4 1 ­6 VOLUME · The adjustment cannot be made when listening with headphones even if + or ­ is pressed. VOLUME +/­ MUTE MUTE TEST VOLUME I To adjust the volume balance between the front and rear speakers While listening to a source, press REAR ­ or +. Pressing + increases and ­ decreases the output level of the rear speakers. SILENT STANDBY/ON STANDBY/ON y · While adjusting, the current level is shown by the lighting of the VOLUME indicators on the front panel. The default level is also shown by the dim lighting of the corresponding indicator. 1 Press STANDBY/ON ( ) to turn on the power. The STANDBY/ON indicator on the front panel lights up. Turn on the AV component connected to this system. Press INPUT repeatedly to select the input source (DIGITAL 1, DIGITAL 2 or ANALOG). The indicator for the selected source lights up on the front panel. Refer to the operation instructions for the component. [. . . ] Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. IMPORTANT : When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Failure to follow instructions could void your FCC authorization to use this product in the USA. [. . . ]