User manual YAMAHA TTR250-2003

[. . . ] OWNER'S MANUAL TTR250R(C) LIT-11626-16-24 5GF-28199-14 EAU03438 EAU00000 INTRODUCTION Congratulations on your purchase of the Yamaha TTR250R. This model is the result of Yamaha's vast experience in the production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and reliability that have made Yamaha a leader in these fields. This manual will give you an understanding of the operation, inspection, and basic maintenance of this machine. [. . . ] Place an oil pan under the engine to collect the used oil. Remove the engine oil filler bolt and drain bolt to drain the oil from the crankcase. Check the washer for damage and replace it if necessary. 4. Remove the oil filter element drain bolt to drain the oil from the oil filter element. NOTE: Skip steps 5­9 if the oil filter element is not being cleaned. Remove the oil filter element cover by removing the bolts. 6-9 PERIODIC MAINTENANCE AND MINOR REPAIR 2 1 Tightening torque: Oil filter element cover bolt: 10 Nm (1. 0 m0kgf, 7. 2 ft0lbf) 10. Install the oil filter element drain bolt, and then tighten it to the specified torque. 1. Add the specified amount of the recommended engine oil, and then install and tighten the oil filler bolt. Oil quantity: Without oil filter element removal: 1. 1 L (0. 97 lmp qt, 1. 16 US qt) With oil filter element removal: 1. 2 L (1. 06 lmp qt, 1. 27 US qt) Total amount (dry engine): 1. 45 L (1. 28 lmp qt, 1. 53 US qt) 6. Remove the oil filter element and O-rings. Check the O-rings for damage and replace them if necessary. Clean the oil filter element with solvent, and then install it. NOTE: Check the oil filter element for damage and replace it if necessary. Install the oil filter element cover by installing the bolts, then tightening them to the specified torque. Tightening torque: Oil filter element drain bolt: 10 Nm (1. 0 m0kgf, 7. 2 ft0lbf) NOTE: Make sure that the O-rings are properly seated. Install the engine oil drain bolt, and then tighten it to the specified torque. Tightening torque: Engine oil drain bolt: 20 Nm (2. 0 m0kgf, 14. 5 ft0lbf) 6 6-10 PERIODIC MAINTENANCE AND MINOR REPAIR cC ECA00133 1 cC ECA00075 6 8 In order to prevent clutch slippage (since the engine oil also lubricates the clutch), do not mix any chemical additives. Do not use oils with a diesel specification of "CD" or oils of a higher quality than specified. In addition, do not use oils labeled "ENERGY CONSERVING II" or higher. 8 Make sure that no foreign material enters the crankcase. 1. Start the engine, and then let it idle for several minutes while checking it for oil leakage. If oil is leaking, immediately turn the engine off and check for the cause. Turn the engine off, and then check the oil level and correct it if necessary. After changing the engine oil, make sure to check the oil pressure as described below. 8 Start the engine and keep it idling until oil flows out. [. . . ] Store it in a cool, dry place and charge it once a month. Do not store the battery in an excessively cold or warm place (less than 0 °C [30 °F]) or more than 30 °C [90 °F]). For more information on storing the battery, see page 6-30. NOTE: Make any necessary repairs before storing the machine. 7 7-5 EAU01038 SPECIFICATIONS Specifications Model Dimensions Overall length Overall width Overall height Seat height Wheel base Ground clearance Minimum turning radius Basic weight (with oil and full fuel tank) Engine Engine type Cylinder arrangement Air-cooled 4-stroke, DOHC Forward - inclined single cylinder 249 cm3 73. 0 × 59. 6 mm (2. 87 × 2. 35 in) 10. 2:1 Electric starter Wet sump Quantity Without oil filter element replacement With oil filter element replacement Total amount (dry engine) 8-1 1. 1 L (0. 97 Imp qt, 1. 16 US qt) 1. 2 L (1. 06 Imp qt, 1. 27 US qt) 1. 45 L (1. 28 Imp qt, 1. 53 US qt) 2, 095 mm (82. 5 in) 835 mm (32. 9 in) 1, 260 mm (49. 6 in) 915 mm (36 in) 1, 405 mm (55. 3 in) 305 mm (12 in) 2, 200 mm (86. 6 in) 124 kg (273 lb) TTR250R(C) Engine oil Type 0° 10° 30° 50° 70° 90° 110° 130°F YAMALUBE 4 (10W30) or SAE 10W30 YAMALUBE 4 (20W40) or SAE 20W40 ­20° ­10° Recommended engine oil classification: 0° 10° 20° 30° 40° 50°C API Service SE, SF, SG type or higher cC In order to prevent clutch slippage (since the engine oil also lubricates the clutch), do not mix any chemical additives. [. . . ]