User manual YAMAHA TX-2000

[. . . ] 3 Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. 4 Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in an environment with high humidity (i. e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury. 5 Avoid installing this unit where foreign objects may fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. [. . . ] · North, Central and South America: 100 kHz/10 kHz · Other areas: 50 kHz/9 kHz Before setting this switch, disconnect this unit's AC power plug from the AC wall outlet. FREQUENCY STEP FM AM 100kHz 10kHz 50kHz 9kHz 8 CONNECTIONS Connecting an amplifier CAUTION Do not connect this unit or other components to the main power until all connections between components are complete. This unit (U. S. A. model) FM ANT GND AM ANT FREQUENCY STEP LINE OUT VOLTAGE SELECTER Note Be sure to connect the left ("L") and right ("R") LINE OUT jacks to the corresponding (left and right) input jacks of the amplifier. 220V-240V 75 UNBAL R FM AM 100kHz 10kHz 50kHz 9kHz L 110V-120V 2 SETUP To an AC wall outlet R L Audio pin cable (included) R L Amplifier POWER CD/DVD STANDBY PHONO TUNER STANDBY POWER ON OFF AUX MD TAPE CD/DVD TUNER PHONO PURE DIRECT CD/DVD DIRECT AMP MD TAPE AUX u + VOLUME TUNER STANDBY /ON VOLUME PRESET INPUT PHONES SPEAKERS A B 3 ON OFF 4 4 5 d BASS 1 2 1 2 3 3 4 4 5 2 ­ TREBLE 1 1 2 3 3 BALANCE 1 2 1 2 3 4 L5 4 5R LOUDNESS 1 2 3 4 5 6 7 FLAT ­30dB 10 9 REC OUT TAPE MD AUX CD/DVD TUNER PHONO A/B/C/D/E A/B DISPLAY w DIR A e f DIR B REC DISC ­5 + ­5 + b s a CD TAPE p Controlling this unit with a remote control This unit has a remote control sensor. It receives signals from a remote control provided with a YAMAHA amplifier or AV receiver. Notes · Do not place any large obstacles between the remote control and this unit. · If the remote control sensor is directly illuminated by strong lighting (especially an inverter type fluorescent lamp), you may not be able to control this unit using the remote control. In this case, reposition this unit to avoid direct lighting. FREQ/TEXT EON FM/MW/LW EDIT PTY SEEK MEMORY TUNING MODE MODE START MAN'L/AUTO FM AUTO/MAN'L A/B/C/D/E TUNING POWER 1 2 3 4 5 6 7 8 l h Approximately 6 m 30 30 English 9 CONNECTIONS Connecting the power supply cord Connecting the AC power cord Plug the power cord into an AC wall outlet. Turning on the power When all connections are complete, turn on the power of this unit. POWER Memory back-up The memory back-up circuit prevents the stored data from being lost. However, the stored data will be lost if this unit is turned off for more than one week even when the power cord is connected. FREQ/TEXT EON FM/MW/LW EDIT PTY SEEK MEMORY TUNING MODE MODE START MAN'L/AUTO FM AUTO/MAN'L A/B/C/D/E TUNING POWER 1 2 3 4 5 6 7 8 l h VOLTAGE SELECTOR (Asia and General models only) The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply. Voltages are 110-120/220-240 V AC, 50/60 Hz. VOLTAGE SELECTOR Press POWER to turn on the power of this unit. POWER 220V-240V 110V-120V (Asia and General models) 10 TUNING TUNING Automatic and manual tuning There are 2 tuning methods; automatic and manual. Automatic tuning is effective when station signals are strong and there is no interference. Manual tuning If the signal from the station you want to select is weak, tune into it manually. Manually tuning into an FM station will automatically switch the tuner to monaural reception to increase the signal quality. Automatic tuning 1 1 2 FREQ/TEXT EON FM/MW/LW EDIT PTY SEEK MEMORY 2 TUNING MODE MODE START MAN'L/AUTO FM AUTO/MAN'L A/B/C/D/E TUNING POWER 1 2 3 4 5 6 7 8 l h FREQ/TEXT EON FM/MW/LW EDIT PTY SEEK MEMORY TUNING MODE MODE START MAN'L/AUTO FM AUTO/MAN'L A/B/C/D/E TUNING POWER 1 2 3 4 5 6 7 8 l h 3 3 1 Press FM/AM (FM/MW/LW for U. K. and Europe models) to select the reception band. OPERATIONS MHz Notes When tuned into a station, the front panel display shows the frequency of the station received. · Any stored station data existing under a preset number is cleared when you store a new station under that preset number. · The reception mode (stereo or monaural) is stored along with the station frequency. 2 Press A/B/C/D/E repeatedly to select a preset station group (A to E) in the front panel display. The station group is displayed in the front panel display. A/B/C/D/E 3 Press MEMORY (MAN'L/AUTO FM). The MEMO indicator flashes for about 5 seconds. MEMORY MAN'L/AUTO FM MEMO Flashes English 13 TUNING Selecting preset stations You can tune any desired station simply by selecting the preset station number under which it was stored. FREQ/TEXT EON FM/MW/LW EDIT PTY SEEK MEMORY TUNING MODE Exchanging preset stations You can exchange the assignment of two preset stations with each other. The example below describes the procedure for exchanging preset station "E1" with "A5". MODE START MAN'L/AUTO FM AUTO/MAN'L A/B/C/D/E TUNING 2, 4 h FREQ/TEXT EON FM/MW/LW EDIT POWER 1 2 3 4 5 6 7 8 l PTY SEEK MEMORY TUNING MODE 1 1 2 POWER MODE START MAN'L/AUTO FM AUTO/MAN'L A/B/C/D/E TUNING 1 2 3 4 5 6 7 8 l h Press A/B/C/D/E repeatedly to select a preset station group (A to E) in the front panel display. The station group is displayed in the front panel display. A/B/C/D/E 3 1 2 3 Select preset station "E1". See "Selecting preset stations". "E1" and the EDIT indicator flash in the front panel display. EDIT 2 Press a preset station number button to select the preset station number (1 to 8). The preset station number appears in the front panel display along with the station band and frequency. 1 2 3 4 5 6 7 8 ST MHz EDIT AUTO ST 3 MHz Select preset station "A5" using A/B/C/D/E and the preset station number buttons. "A5" and the EDIT indicator flash in the front panel display. Note In some cases, you may not be able to select a preset station that could be received using the automatic tuning method. This is due to the large volume of Program Identification (PI) data received along with the station. ST MHz EDIT 14 TUNING 4 Press EDIT again. [. . . ] 85 dB · Selectivity (two signals, 40 kHz dev. , ±300 kHz) [U. K. , Europe, Australia and Asia models only] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 dB · Signal to Noise Ratio (IHF) [U. S. A. , Canada, General and China models] Mono . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [U. K. , Europe, Australia and Asia models] (DIN-weighted) Mono (40 kHz dev. ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]