User manual YAMAHA TX6N

[. . . ] EN DE FR ES IT RU Explanation of Graphical Symbols C A U TI ON RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The above warning is located on the top of the unit. IMPORTANT SAFETY INSTRUCTIONS 1 2 3 4 5 6 7 8 Read these instructions. Install in accordance with the manufacturer's instructions. [. . . ] These can be controlled from the panel of the TXn unit or via Amp Editor. Speaker processor libraries created on the Yamaha DME series or the SP2060 can also be used. About Setup Attaching the handles You can attach the handles to the amplifier using the supplied flat-head screws. Follow the steps below to attach the handles: 1. Attach the handles to the amplifier by tightening the flat-head screws into the four screw holes for each handle. Replace the rack mount brackets. Adjusting the position in the rack If there is insufficient space between the rear of the amplifier and the rack, you can adjust the position of the rack mount brackets so that the front panel of the amplifier protrudes from the front of the rack by 22 mm. Related manuals and software This manual primarily explains how to set up the TXn at the time of installation. Manuals that contain detailed explanations of the TXn and Amp Editor, as well as Amp Editor itself, can be downloaded from the following website. http://www. yamahaproaudio. com/ · List of related manuals TX6n/5n/4n Reference Manual Amp Editor Installation Guide Amp Editor Owner's Manual NOTE Provides a detailed explanation of the TXn's panel operations, etc. Explains the installation and uninstallation procedures for Amp Editor. Explains how to use Amp Editor. · In order to view the downloaded manuals, Adobe Reader must be installed in your computer. If you don't have Adobe Reader, please access the Adobe Corporation's website at the following URL, and download Adobe Reader (free of charge). http://www. adobe. com/ TX6n/5n/4n Owner's Manual 7 Firmware Updates The firmware version of the TXn itself can be checked from the TXn's panel and from Amp Editor. You can update the firmware via Amp Editor. For the update procedure, refer to the Amp Editor Owner's Manual. You can download the latest firmware from the "Downloads" page on the following website. http://www. yamahaproaudio. com/ Preparation [MUTE] buttons [POWER] switch Function buttons [ENTER] button [HOME] button Connecting the AC Power Cable · Be sure to turn all devices OFF before connecting AC mains power. CAUTION Switching the Power Status between Standby and On 1. Hold down the panel [HOME] button for at least three seconds. The TXn's display will show the HOME screen, and then a message of "Turning power on: Are you sure?" or "Going Standby: Are you sure?" will appear. Insert the plug into an AC outlet. Be sure to use an AC outlet of the voltage specified for the device. Turning the Power on and off · To prevent the initial power-on surge from generating a large noise spike or damaging your speaker system, turn the devices on in the following order: audio sources, mixer (such as M7CL or PM5D), and finally power amplifiers. Reverse this order when turning power off. 2. Press the panel [ENTER] button, and the power status will switch between Standby and On. NOTE CAUTION · Standby is a state in which the speaker output's power amp section is off (operation other than speaker output will continue). 1. Press the front panel [POWER] switch to the "ON" position to turn the power on. Switching Mute on/off Hold down the [MUTE] button of the channel you want to mute for at least one second. The channel's output will be muted, and the [MUTE] indicator will light. To switch mute off, press the [MUTE] button again for at least one second. 2. Press the [POWER] switch to the "OFF" position to turn off the power. NOTE · The settings at the time you powered-off are remembered. When you turn on the power to the TXn, it will start up with the same settings. Resume" setting to set up the TXn so that at startup it will recall the scene number selected before you turned off the power to the device. · Do not turn off the power while the upper part of the display indicates "Do Not Turn Off!" Otherwise, a malfunction may occur. [. . . ] Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 POLAND Yamaha Music Europe GmbH Branch Sp. z o. o. 17 Stycznia 56, PL-02-146 Warszawa, Poland Tel: 022-868-07-57 ASIA THE PEOPLE'S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co. , Ltd. 2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu, Shanghai, China Tel: 021-6247-2211 U. S. A. Yamaha Corporation of America 6600 Orangethorpe Ave. , Buena Park, Calif. [. . . ]