User manual YAMAHA TX802E

[. . . ] If you must use an extension cord, the minimum wire size for a 25" cord (or less) is 18 AWG. NOTE: The smaller the AWG number, the larger the current handling capacity. For longer extension cords, consult a local electrician. This Product should be used only with the components supplied or; a cart, rack, or stand that is recommended by Yamaha. [. . . ] r START/STOP Button Starts and stops fan rotation. t DC 12V IN Jack y MOTOR OUT Terminal u MOTOR IN Terminal i 8P DIN Cable o AC Adapter q Driver (Player Side) 2 CONFIRMATION OF PACKING CONTENTS The shipping carton of your TX802E should contain the parts shown below. Before assembling the instrument, confirm that all parts are included as listed. : TX802E * In the event that a part is missing, please contact the shop where the instrument was purchased. q Natural Tone Bars i Rail (1) : Player Side Name Plate o Rail (2) : Player Side Rail Clamp Posts (Larger number than parts !0 and !1) w Accidental Tone Bars !0 Rail (3) : Audience Side Rail Clamp Posts !1 Rail (4) : Audience Side e Resonators (Natural Tone Side) YAMAHA Logo Posts !2 Leg (Large) !3 Leg (Small) r Resonators (Accidental Tone Side) !4 AC Adapter t Sustain Damper !5 Synchro Belt (Fan Belt): 2 pcs. y Reinforcement Stay Vibes Drive Unit: YVM-300 !6 Driver !7 Controller u Pedal Stay !8 8P DIN Cable 3 CONFIRMATION OF PACKING CONTENTS : YV-3910/3710 The shipping carton of your YV-3910/3710 should contain the parts shown below. Before assembling the instrument, confirm that all parts are included as listed. * In the event that a part is missing, please contact the shop where the instrument was purchased. q Natural Tone Bars u Rail (1) : Player Side Name Plate i Rail (2) : Player Side Rail Clamp Posts (Larger number than parts o and !0) w Accidental Tone Bars o Rail (3) : Audience Side Rail Clamp Posts !0 Rail (4) : Audience Side e Resonators (Natural Tone Side) YAMAHA Logo Posts !1 Leg (Large) !2 Leg (Small) r Resonators (Accidental Tone Side) !3 AC Adapter t Sustain Damper !4 Synchro Belt (Fan Belt): 2 pcs. Vibes Drive Unit: YVM-300 y Pedal Stay !5 Driver !6 Controller !7 8P DIN Cable 4 CONFIRMATION OF PACKING CONTENTS : YV-3910/3710 s Dividable Parts and Collapsible Parts (YV-3910/3710 only) The YV-3910's/YV-3710's large parts are designed to either divide or collapse. When the instrument is broken down, its compact size makes it easy to transport and storage requires a minimum amount of space. q Rails The rails fold in from the center. q Pedal Stay The pedal stay divides into left and right sections and the pedal itself. Loosen the 2 wing nuts and remove the stays from the pedal attachment. Loosen q Sustain Damper The sustain damper divides into 2 sections. Loosen the bolt and separate left and right sections. Loosen q Resonators Both resonators divide into two sections. Loosen both bolts and separate left and right sections. * When assembling the resonators, make sure that the pin and notch are properly aligned. Loosen Pin Notch 5 ASSEMBLY : YV-3910/3710/3700 For safety, assembly should be performed by at least 2 persons in a location with sufficient space. We recommend to you to assemble the instrument on a soft rug or carpet. z Connect the large and the small leg using the reinforcement stay and pedal stay. * Before proceeding, make sure that the slide leg fixing bolts of the large and small leg are securely fastened. Leg (Large) The tip of each slide leg fixing bolt must be tightly seated in one of the slide leg notches. q TX802E : There are two controller mounting pins on the high sound side of rail (1). Align the two holes in the controller mounts with these pins and hook the controller onto the pins one side at a time. q TX802E High Sound Side Controller mounting pins High Sound Side q YV-3910/3710 Fixing bolt Controller hunger Controller Controller , Connect the driver with the controller. 8-1 Connect the MOTOR IN terminal of the driver with the MOTOR OUT terminal of the controller using the supplied 8P DIN cable*. To connect align the arrow mark ( ) on the plug with the screw next to the jack. Controller Screw Arrow Mark Driver Screw Arrow Mark 8P DIN Cable * In case the 8P DIN cable is misplaced, the following spare part may be ordered: Part No. W5128092 Part Name 8P DIN Cable Specification L=220 15 ASSEMBLY: YV-3910/3710/3700 . Set the synchro belts (fan belts)*. 9-1 First, wrap the synchro belt around the driver pulley and then carefully slide it over the fan side pulley. * Note For Service Personnel If the belt cannot be mounted because the distance between pulleys is too wide, or the belt slips due to a too narrow pulley distance, loosen the two driver positioning screws (see illustration below) to adjust the pulley distance (belt tension). Tighten the screws securely after adjustment. Driver Side Synchro Belt (Fan Belt) Driver Positioning Screws Pulley Fan Side Synchro Belt (Fan Belt) * Slide belt over the pulley. Pulley * In case the belt is misplaced or worn, the following spare part may be ordered: Part No. W5128092 Part Name Synchro Belt Specification 18OTN15-3. 0 16 ASSEMBLY: YV-3910/3710/3700 /0 ADJUSTMENTS 10-1 Pedal Stroke Adjustment Loosen the center rod fixing bolts to adjust the protruding length of the center rod to the desired pedal stroke, and retighten the bolts. The recommended stroke (distance between pedal and floor) is 9/16" to 13/16" (1. 5 to 2 cm). 10-2 Wire Clip Adjustment For shipment the wire clip is initially set at a low position for packing reasons. For normal use this clip should be adjusted as follows: With the pedal released loosen the fixing bolt of the wire clip, shift the clip up until distance A in the illustration below is 1/16" to 1/8" (1 to 3 mm), and tighten the wing bold in this position. [. . . ] (All four slide legs are identical. ) Slide Legs Tighten 21 ASSEMBLY : YV-2700/2700G/1600A/520 4 Place the large leg, small leg, pedal stay and reinforcement stay* so that after assembly each part will be positioned as illustrated. (* YV-1600A/520 is not equipped with a reinforcement stay) Low Sound Side Leg (Large) Reinforcement Stay* Audience Side Leg (Small) Pedal Stay Pedal High Sound Side Player Side 5 Connect the large leg and small leg with the pedal stay and the reinforcement stay. Insert the pedal stay with its notch facing up into the lower joint of the large leg as far as it will go (aligning the notch with the fixing bolt) and tighten the fixing bolt securely. * The hole next to the notch serves as a reference for the correct insertion position. [. . . ]