User manual YAMAHA V-MAX-2000

[. . . ] If you have any questions concerning the operation or maintenance of your motorcycle, please consult a Yamaha dealer. The design and manufacture of this Yamaha motorcycle fully comply with the emissions standards for clean air applicable at the date of manufacture. Yamaha has met these standards without reducing the performance or economy of operation of the motorcycle. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to the recommended maintenance schedules and operating instructions contained within this manual. IMPORTANT MANUAL INFORMATION EAU10130 Particularly important information is distinguished in this manual by the following notations: The Safety Alert Symbol means ATTENTION! [. . . ] Spark plug gap Spark plug gap: 0. 8­0. 9 mm (0. 031­0. 035 in) 6-10 PERIODIC MAINTENANCE AND MINOR REPAIR NOTE: The engine oil should be between the minimum and maximum level marks. Place an oil pan under the engine to collect the used oil. Remove the engine oil filler cap and drain bolt to drain the oil from the crankcase. NOTE: Skip steps 4­6 if the oil filter cartridge is not being replaced. Remove the oil filter cartridge with an oil filter wrench. 6 1. If the engine oil is below the minimum level mark, add sufficient oil of the recommended type to raise it to the correct level. To change the engine oil (with or without oil filter cartridge replacement) 1. Start the engine, warm it up for several minutes, and then turn it off. NOTE: An oil filter wrench is available at a Yamaha dealer. Apply a thin coat of engine oil to the O-ring of the new oil filter cartridge. 1. Engine oil drain bolt 6-11 PERIODIC MAINTENANCE AND MINOR REPAIR Recommended engine oil: See page 8-1. Oil quantity: Without oil filter cartridge replacement: 3. 50 L (3. 70 us. qt) (3. 08 Imp. qt) With oil filter cartridge replacement: 3. 80 L (4. 02 us. qt) (3. 34 Imp. qt) ECA11620 1. Remove the oil filler bolt and drain bolt to drain the oil from the final gear case. Install the final gear oil drain bolt, and then tighten it to the specified torque. Tightening torque: Final gear oil drain bolt: 23 Nm (2. 3 m·kgf, 17 ft·lbf) EAU20070 Coolant The coolant level should be checked before each ride. In addition, the coolant must be changed at the intervals specified in the periodic maintenance and lubrication chart. EAU20240 NOTE: The coolant should be between the minimum and maximum level marks. 4. Add the recommended final gear oil to the brim of the filler hole. Recommended final gear oil: Hypoid gear oil SAE 80 (API GL4) or multi-grade hypoid gear oil SAE 80W-90 Oil quantity: 0. 20 L (0. 21 us. qt) (0. 18 Imp. qt) To check the coolant level 1. Place the vehicle on the centerstand and hold it in an upright position. (See page 6-8. ) NOTE: G The coolant level must be checked on a cold engine since the level varies with engine temperature. G Make sure that the vehicle is positioned straight up when checking the coolant level. A slight tilt to the side can result in a false reading. Check the coolant level in the coolant reservoir. 1. Minimum level mark 6 NOTE: GL4 is a quality rating. Hypoid gear oils rated GL5 or GL6 may also be used. [. . . ] 6-4 Maintenance, emission control system. . . 6-3 Maintenance, periodic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 Maintenance record. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5 Model label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]