User manual YAMAHA VINO CLASSIC-2006

[. . . ] 1 2 3 4 5 6 7 OWNER'S MANUAL 8 9 XC50V LIT-11626-19-49 3D1-F8199-10 1 2 3 4 5 6 7 8 9 EAU10041 EAU10050 INTRODUCTION EAU10090 Congratulations on your purchase of the Yamaha VINO. This model is the result of Yamaha's vast experience in the production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and reliability that have made Yamaha a leader in these fields. 1 This manual will give you an understanding of the operation, inspection, and basic maintenance of this scooter. [. . . ] Do not attempt to diagnose such problems yourself. Instead, have a Yamaha dealer check the vehicle. Check the spark plug for electrode erosion and excessive carbon or other deposits, and replace it if necessary. Specified spark plug: CR7E (NGK) wire thickness gauge and, if necessary, adjust the gap to specification. Tightening torque: Spark plug: 13 Nm (1. 3 m · kgf, 9. 4ft · lbf) 1 1 NOTE: If a torque wrench is not available when installing a spark plug, a good estimate of the correct torque is 1/4~1/2 turn past finger tight. However, the spark plug should be tightened to the specified torque as soon as possible. Install the partition and the panel. 2 3 4 5 6 7 8 9 ZAUM00** 1. Spark plug wrench Spark plug gap: 0. 7 ~ 0. 8 mm (0. 028 ~ 0. 031 in) 2. Clean the surface of the spark plug gasket and its mating surface, and then wipe off any grime from the spark plug threads. Install the spark plug with the spark plug wrench, and then tighten it to the specified torque. To install the spark plug 1. Measure the spark plug gap with a 6-7 Engine oil<IXE> PERIODIC MAINTENANCE AND MINOR REPAIR EAUT1460 Engine oil and oil strainer 1 2 3 4 5 6 7 8 9 4. If the engine oil is below the minimum level mark, add sufficient oil of the recommended type to raise it to the correct level. 6-8 The engine oil level should be checked before each ride. In addition, the oil must be changed and the oil strainer cleaned at the intervals specified in the periodic maintenance and lubrication chart. To check the engine oil level 1. Place the vehicle on the centerstand. NOTE: Make sure that the vehicle is positioned straight up when checking the oil level. A slight tilt to the side can result in a false reading. Start the engine, warm it up for several minutes, and then turn it off. ZAUM00** 5. Insert the dipstick into the oil filler hole, and then tighten the oil filler cap. 1 2 3 To change the engine oil and clean the oil strainer 1. Start the engine, warm it up for several minutes, and then turn it off. Place an oil pan under the engine to collect the used oil. 1. Wait a few minutes until the oil settles, remove the oil filler cap, wipe the dipstick clean, insert it back into the oil filler hole (without screwing it in), and then remove it again to check the oil level. NOTE: The engine oil should be between the minimum and maximum level marks. 1 ZAUM00** 1. Remove the engine oil filler cap and the engine oil drain bolts A and B to drain the oil from the crankcase. PERIODIC MAINTENANCE AND MINOR REPAIR 4 3 2 1 NOTE: Make sure that the O-ring is properly seated. Install engine oil drain bolt A, and then tighten both drain bolts to their specified torques. Tightening torque: Engine oil drain bolt A: 23 Nm (2. 3 m · kgf, 16. 6 ft · lbf) Engine oil drain bolt B: 32 Nm (3. 2 m · kgf, 23. 1 ft · lbt) ECAT1020 8. [. . . ] 6-24 Turn signal switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 D Dimmer switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 E Engine break-in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]