User manual YAMAHA VXS10S/VXS10SW/VXS10ST/VXS10STW

[. . . ] Even if the output power of the amplifier is lower than the power capacity of this device (PGM), use of excessive input signals resulting in clipping may cause damage to the device. Malfunction or fire may occur especially when the following sounds or noises are generated: - feedback, when using a microphone - continuous and extreme volume sound from a musical instrument - extreme continuous distorted sound - noise caused by plugging/unplugging the cable while the amplifier is turned on SPECIFICATIONS Type Component Nominal impedance Power rating (IEC, 100h) *1 VXS10S/VXS10SW VXS10ST/VXS10STW Subwoofer, Bass reflex 10" (25 cm) Cone driver, Dual voice coil 8Ω+8Ω – 100 W + 100 W – 200 W + 200 W – 400 W + 400 W – 96 dB SPL 96 dB SPL 125 dB SPL – 45 Hz – 250 Hz 45 Hz – 250 Hz Network: Low-pass filter 6 dB/Oct, 200 Hz Acoustic filter: Low-pass filter 6 dB/Oct, 200 Hz Network: High-pass filter 6 dB/Oct, 200 Hz 8 Ω load per satellite output recommended *4 Euroblock (4 pin) × 1: Euroblock (4 pin) × 1: Input (CH1: +/-, CH2: +/-) Input (input: +/-, loop-thru: +/-) Euroblock (4 pin) × 1: Satellite output (ST1: +/-, ST2: +/-) – Euroblock (5 pin) × 1: transformer taps – 200 W, 100 W, 50 W, 25 W – 200 W, 100 W, 50 W Full-range power limiting to protect network and transducers No Rectangle MDF VXS10S/VXS10ST: Black (PVC, approximate value: Munsell N3) VXS10SW/VXS10STW: White (PVC, approximate value: Munsell 3. 5PB9. 0/1) 260 × 500 × 389 mm (10. 2" × 19. 7" × 15. 3") 16. 5 kg (36. 4 lb) 19. 5 kg (43. 0 lb) NOISE PGM MAX NOTICE To avoid the possibility of malfunction/damage to the product or damage to other property, follow the notices below. CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following: ● Handling and Maintenance • Do not place vinyl, plastic or rubber objects on the device, since this might discolor the cabinet. [. . . ] Attempting to lift the device by yourself may damage your back, result in other injury, or cause damage to the device itself. Transformer taps Overload protection Magnetically shielded Enclosure Finish 70 V 100 V Shape Cabinet material Dimensions (Speaker only) Net weight (Speaker only) Connections • Before connecting the device to a power amplifier, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum. • Use only speaker cables for connecting speakers to the speaker connectors. Use of other types of cables may result in fire. *1: Pink noise with 6 dB crest factor. *2: Half-space (2π) *3: Calculated based on power rating and sensitivity, exclusive of power compression. *4: Impedance lower limit (per satellite output) VXS10S/VXS10SW: 4 Ω, VXS10ST/VXS10STW: 8 Ω Specifications and descriptions in this owner’s manual are for information purposes only. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. The dimensions are shown overleaf. ● About This Manual The illustrations as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your device. Yamaha cannot be held responsible for damage caused by improper use or modifications to the device. Maintenance • Do not wipe the outer packaging with benzine, thinner, or synthetic detergent and do not use electrical contact cleaner. These may damage the outer packaging and dissolve the parts. INSTALLING THE SPEAKER When installing the speaker on the floor, attach the rubber spacers to the underside of the speaker to provide support. When installing the speaker on a wall or ceiling, use the included brackets or optional U-bracket UB-DXR8. Ensure that the wall/ceiling is sufficiently strong. This package does not include the mounting hardware to install the included brackets/safety wire or the UB-DXR8. If you are not sure what materials are required for installation, consult a specialist. Wall installation (using included brackets) Ceiling installation (using optional bracket UB-DXR8) 2 After loosening the terminal screws of the Euroblock connector with a flat-blade screwdriver, insert the cable into each terminal and tighten the screws. [. . . ] Doing so will cause the wire to break. 2 Pass the bracket of the safety wire through the loop on the other end, and pull tight up against the eyebolt. 1 CONNECT THE WIRING TO THE CONNECTOR Connect the cable from the amplifier to the “INPUT” socket, and the cable being connected to other speakers to the “SATELLITE SPEAKERS” socket. A signal input to CH1 of INPUT is output from ST1 of SATELLITE SPEAKERS, and signal input to CH2 of INPUT is output from ST2 of SATELLITE SPEAKERS. For VXS10ST/VXS10STW, connect the included 5-pin Euroblock connector as shown below and set the appropriate wattage when using 100 V/70 V line. [. . . ]