User manual YAMAHA VXS8/VXS8W/VXS5/VXS5W

[. . . ] Even if the output power of the amplifier is lower than the power capacity of this device (PGM), use of excessive input signals resulting in clipping may cause damage to the device. Malfunction or fire may occur especially when the following sounds or noises are generated: - feedback, when using a microphone - continuous and extreme volume sound from a musical instrument - extreme continuous distorted sound - noise caused by plugging/unplugging the cable while the amplifier is turned on SPECIFICATIONS Type Component VXS5/VXS5W 2-way, Bass-reflex 8" (20 cm) Cone driver 5-1/4" (13 cm) Cone driver 1" (2. 5 cm) Soft dome tweeter 3/4" (2 cm) Soft dome tweeter 100° H × 100° V 120° H × 120° V 8Ω 90 W 75 W 180 W 150 W 360 W 300 W 91 dB SPL 89 dB SPL 117 dB SPL 114 dB SPL 51 Hz – 20 kHz 62 Hz – 20 kHz 2. 8 kHz 3 kHz Euroblock (4 pin) × 1 (input: +/-, loop-thru: +/-) Max. wire size 12 AWG (2. 5 mm2) 60 W, 30 W, 15 W, 7. 5 W 30 W, 15 W, 7. 5 W, 3. 8 W 60 W, 30 W, 15 W 30 W, 15 W, 7. 5 W Full-range power limiting to protect network and transducers No IP35 Rectangle ABS PC/ASA Powder coated perforated aluminum (t=1 mm) Aperture ratio: 51% VXS8/VXS5: Black (Not painted, approximate value: Munsell N3) VXS8W/VXS5W: White (Not painted, approximate value: Munsell 9. 3) 278 × 430 × 239 mm 176 × 280 × 163 mm (10. 9" × 16. 9" × 9. 4") (6. 9" × 11. 0" × 6. 4") 8. 2 kg (18. 1 lbs) 3. 6 kg (7. 9 lbs) Packaged in pair VXS8/VXS8W NOTICE To avoid the possibility of malfunction/damage to the product or damage to other property, follow the notices below. Location • Do not place the device in an unstable position where it might accidentally fall over. [. . . ] • Do not touch the speaker driver unit. LF HF Coverage angle (500 Hz – 4 kHz on average) Nominal impedance Power rating NOISE (IEC, 100h) *1 PGM MAX Sensitivity (1W, 1m) *2 Maximum SPL (Calculated, 1m) *3 Frequency range (-10 dB) *2, *4 Crossover frequency Connector Transformer taps 70 V 100 V Overload protection Magnetically shielded Dust and water resistant *5 Enclosure Shape Cabinet material Baffle material Grille material Finish Dimensions (Speaker only) (W × H × D in vertical cabinet orientation) Net weight (Speaker only, 1 piece) Packaging Connections • Before connecting the device to a power amplifier, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum. • Use only speaker cables for connecting speakers to the speaker connectors. Use of other types of cables may result in fire. Maintenance • Do not wipe the outer packaging with benzine, thinner, or synthetic detergent and do not use electrical contact cleaner. These may damage the outer packaging and dissolve the parts. ● About This Manual The illustrations as shown in this manual are for instructional purposes only, and may appear somewhat different from those on your device. Yamaha cannot be held responsible for damage caused by improper use or modifications to the device. *1: Pink noise with 6 dB crest factor. *2: Half-space (2π) *3: Calculated based on power rating and sensitivity, exclusive of power compression. *4: When connecting with low impedance *5: IP34 when installing the speaker to the ceiling vertically. Specifications and descriptions in this owner’s manual are for information purposes only. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer. The dimensions are shown overleaf. INSTALLING THE SPEAKERS Install the speakers onto the wall/ceiling with the supplied brackets. Ensure that the wall/ceiling is sufficiently strong. Illustrations in this manual are for the VXS5. The installation method is the same for other models. Pre-installation (Preparation of the cable) Use stranded wire for cables attached to the Euroblock connector. [. . . ] Loosen the angle adjustment bolt with the supplied hexagon wrench, adjust the angle of the speaker, and tighten the angle adjustment bolt to fix the speaker (indication of torque: 8 N·m). NOTE • Guide marked on the mounting bracket is every 10°. • (VXS8/VXS8W only) When installing the speaker to the wall with a vertical angle of 30° or less, attach the supplied stopper screw. 1 INSTALL THE BRACKET BASE ONTO THE WALL /CEILING 1 Put the bracket base onto the wall/ceiling and mark the position for the screws/bolts and cables. [. . . ]