User manual YAMAHA WOODEN RECORDER GREAT BASS

[. . . ] · When disconnecting the power cord from the wall outlet, grasp the plug; do not pull the cord. · Be sure to read the "TROUBLESHOOTING" section on common operating errors before concluding that this unit is faulty. Installation · Install this unit in a well-ventilated, cool, dry, clean place with at least 10 cm clearance on the top, right and left, and at the back of this unit -- away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. · Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. To prevent fire or electrical shock, do not place this unit where it may get exposed to rain, water, and/or any type of liquid. [. . . ] The higher setting adds more blue and the lower setting adds more red. Select the appropriate setting depending on the content to be projected. WHITE BALANCE S Fine-adjusts the balance of each color (R, G, B). CONTRAST (R, G, B) BRIGHTNESS (R, G, B) WHITE BOOST Optically adjusts the luster of the white part of the projected image. A/B/C/D/E 1 to 5 ­128 to 127 MENU ­128 to 127 0 to 127 LOW/MID-L/MID/HIGH 50% to 124% ­12. 4% to 12. 4% 0 to 10 English E-15 Menu structure I 2 <SIGNAL>. . . . . . . . . Adjustment cannot be made without any input signal. Input signal Video/Component/RGB Menu item ASPECT S Sets the aspect ratio of displaying the image on the screen. "AUTO" automatically switches to the most appropriate mode. "NORMAL" (THROUGH) projects the image as the input signal is sent. "SQUEEZE" desqueezes the squeezed image. "ZOOM" projects the image scaled up with a certain ratio. "ZOOM -SUBTITLE-" displays the subtitle. "THROUGH -SQUEEZE-" displays the image with its width scaled up. INPUT B SIGNAL S Selects the type of input signal sent to the INPUT B jacks. LANGUAGE S Selects the language used on the menu. POWER SAVING When no signal is received at the input jacks for longer than 15 minutes, this unit automatically turns off the lamp and enters the standby mode if ON is selected. LAMP RUNNING TIME S Displays the total lamp running time. The lamp running time can be reset on the submenu. RESET S Resets all parameters on the menu or parameters in the memory to the factory settings. Choice AUTO/NTSC/NTSC4. 43/PAL/PAL-M/PAL-N/ PAL60/SECAM COMPONENT/RGB PC/RGB TV COMPONENT/RGB PC/RGB TV /ENGLISH/DEUTSCH/ESPAÑOL/ FRANÇAIS/ITALIANO/ OFF/ON -- ALL SETTINGS/ALL MEMORIES/ CURRENT MEMORY I 4 <SETUP> Menu item INSTALLATION S There are four methods to install this unit; tabletop or on-ceiling for front or rear projection. The image can be inverted or rotated according to the setting for the installation method. SCREEN ASPECT Selects 4:3 or 16:9 depending on the screen to be used. If 16:9 is selected, vertical adjustment of the image can be made by changing the value of the item "DIGITAL LENS SHIFT". And automatically makes an adjustment to project the 4:3 input signal without losing any part of it off screen. [. . . ] 800 ANSI lm Contrast ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 900:1 Controls Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RS-232C (D-Sub 9 pin) Trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +12 V when the power is on; 0 V when the power is off (mini jack) Remote control sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]