User manual YAMAHA X2500

[. . . ] IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Failure to follow instructions could void your FCC authorization to use this product in the USA. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class "B" digital devices. [. . . ] ( page 10) * Power is switched ON when the power adaptor is connected (and supplying power) to the main unit. !1 PHONES Jack A pair of headphones connected to this jack (stereo mini) let's you practice or edit patches while monitoring the MAGICSTOMP's sound output through the headphones. Use the Volume Knob e to adjust the volume. * Output is still delivered from the OUTPUT jack i when a pair of headphones is connected to the PHONES jack. 9 Connections CAUTION · In order to prevent electric shock or damage to your equipment, turn OFF the power on the guitar amp, etc. , and set the MAGICSTOMP's volume to its minimum level before making any connections. · Use ONLY a Yamaha AC-10 Power Adaptor (or other adaptor specifically recommended by Yamaha). Using another adaptor may result in damage, overheating or fire, which can be very dangerous. · Make sure to use the recommended AC voltage as indicated on the power adaptor. · The MAGICSTOMP automatically switches "ON" when power is connected and supplied to the device. · Connect an acoustic guitar/electric acoustic guitar or any line level instrument such as a synthesizer, etc. , to the INPUT jack. The MAGICSTOMP can also be connected to the effect loop of an amplifier, mixer, or other similar device. · Set the INPUT LEVEL switch to match the output level of the instrument or device that is connected to the MAGICSTOMP. If the sound is distorted when the switch is set to the HIGH position, change the setting to LOW. If you feel output is low when the switch is set to the LOW position, change the setting to HIGH. · When using patches with stereo output, we recommend connecting the MAGICSTOMP's output jacks to a stereo device. U01/02/03 P97/98/99 P94/95/96 P91/92/93 : : AFR ON or Patch ON/OFF* for U05 Press and hold the + switch. U07/08/09 U10/11/12 U13/14/15 U16/17/18 : : U06«Delay0Arpegg PERFORMANCE0MODE U06«Delay0Arpegg >TRE0fiELVLáRLVL Performance Mode * The setting or effect type determines whether the switch will activate the Auto Feedback Reduction function or switch the patch ON/OFF. ( page 22) 13 Create your own sound s Use the knobs to adjust the effect The three knobs located below the display let you adjust different characteristics of the effect. The parameters that these knobs adjust, differ according to the selected patch. The name of the parameters that these knobs adjust, and the relative knob position of each of the parameters are shown on the lower half of the display. In the example shown below, the following parameter names and knob values are shown starting with the left knob. BASS (Bass): 8. 9, MID (Middle): 4. 0, TRE (Treble): 2. 8 U01«Natural óBASSfiMID0áTRE When the knob's position does not match the value for the selected parameter, you'll need to rotate the knob until it matches the position that corresponds to the parameter value before you can change the setting. Before rotating the knob, its parameter name is shown in the display. 1] When the knob is rotated, the set value (8. 9) is indicated in the display, and will not change until you rotate the knob past the 3 o'clock position. 1] U01«Na óBASS [Fig. 2] U01«Na ó08. 9 U01«Na ó08. 9 After you rotate the knob past the 3 o'clock position, the actual value that corresponds to the knob's position is indicated in the display. [. . . ] Is the volume knob set to "0"? Is the effect's output level set to "0"? · Sound level is low Switch the input level to the "HIGH" position. ( P. 10) · Effect is not active Is the effect's output level set to "0"? Is the effect switched OFF (all lamps are off)? · Can not change to another patch Check the display. [. . . ]