User manual YAMAHA X2500E

[. . . ] Cable/s supplied with this product MUST be used. Failure to follow instructions could void your FCC authorization to use this product in the USA. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class "B" digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. [. . . ] You can also store customized sound patches in your computer. [Edit effects on your computer with a software based patch editor] · Connect the MAGICSTOMP to your computer using the supplied USB cable then use the accompanying "Sound Editor for MAGICSTOMP" to edit effect parameters. Use the Volume Knob e to adjust the volume. * Output is still delivered from the OUTPUT jack i when a pair of headphones is connected to the PHONES jack. 9 Connections CAUTION · In order to prevent electric shock or damage to your equipment, turn OFF the power on the bass amp, etc. , and set the MAGICSTOMP's volume to its minimum level before making any connections. · Use ONLY a Yamaha AC-10 Power Adaptor (or other adaptor specifically recommended by Yamaha). Using another adaptor may result in damage, overheating or fire, which can be very dangerous. · Make sure to use the recommended AC voltage as indicated on the power adaptor. · The MAGICSTOMP automatically switches "ON" when power is connected and supplied to the device. · Connect a bass, guitar or any line level instrument such as a synthesizer, etc. , to the INPUT jack. The MAGICSTOMP can also be connected to the effect loop of an amplifier, mixer, or other similar device. · Set the INPUT LEVEL switch to match the output level of the instrument or device that is connected to the MAGICSTOMP. If the sound is distorted when the switch is set to the HIGH position, change the setting to LOW. If you feel output is low when the switch is set to the LOW position, change the setting to HIGH. · When using patches with stereo output, we recommend connecting the MAGICSTOMP's output jacks to a stereo device. DRIV (Drive): 8. 9, MSTR (Master): 4. 0, TONE: 2. 8 U01/DIST10000000 óDRIVfiMSTRáTONE When the knob's position does not match the value for the selected parameter, you'll need to rotate the knob until it matches the position that corresponds to the parameter value before you can change the setting. Before rotating the knob, its parameter name is shown in the display. 1] When the knob is rotated, the set value (8. 9) is indicated in the display, and will not change until you rotate the knob past the 3 o'clock position. 1] U01¤DI óDRIV [Fig. 2] U01¤DI ó08. 9 U01¤DI ó08. 9 After you rotate the knob past the 3 o'clock position, the actual value that corresponds to the knob's position is indicated in the display. Also, the ¤ mark to the right of the patch number will change to / to indicate that the parameter's value has changed. 3] Once the parameter's value has been changed, the value shown in the display will reflect the position of the knob. 4] If the knob is not moved for a few seconds, the value display will return to the parameter name display. [Fig. 4] U01/DI óñ10. 0 U01/DI óê06. 2 14 Create your own sound OK, now try and edit a patch to your liking. * For more information on parameters of individual effects, refer to the separate "Effect List" sheet. * Parameters for the patch(effect) can only be adjusted when the MAGICSTOMP is in its normal operating mode (when a patch is selected and the effect is switched "ON"). Parameters can not be adjusted if the effect is switched "OFF" or when the MAGICSTOMP is in the Store Mode (page 18), Name Edit Mode (page 20) or Tuner Mode (page 24). After creating something you like, use the store operation ( page 18) to save your settings in the MAGICSTOMP. [. . . ] Is the volume knob set to "0"? Is the effect's output level set to "0"? · Sound level is low Switch the input level to the "HIGH" position. ( P. 10) · Effect is not active Is the effect's output level set to "0"? Is the effect switched OFF (all lamps are off)? · Can not change to another patch Check the display. [. . . ]