User manual YAMAHA XM-4080

[. . . ] EN DE FR ES Español OWNER'S MANUAL BEDIENUNGSANLEITUNG MODE D'EMPLOI MANUAL DE INSTRUCCIONES Français Deutsch English POWER AMPLIFIER FCC INFORMATION (U. S. A. ) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. [. . . ] After three seconds, the protection system deactivates automatically and the amplifier is ready for normal operation. If a DC voltage is detected at the amplifier's outputs Air intake Air exhaust The protection system activates if a DC voltage is detected at the amplifier's outputs. Once the DC voltage problem is corrected, the protection system deactivates automatically and the amplifier is ready for normal operation. If the amplifier overheats When overheating occurs, the PROTECT/MUTE indicator lights. You should immediately turn off the amplifier and allow it time to cool down. See the Precautions section of this Owner's Manual for ways to prevent the amplifier from overheating. Security cover If you want to keep the volume settings from being modified, attach the included security cover using the screw holes shown below, so that the volume controls are inaccessible. 3 CLIP/LIMIT indicator A channel's CLIP indicator lights up when its output distortion exceeds 1% (i. e. , clipping). Output signal clipping is typically caused by excessive input signal levels. When this happens, the limiter is engaged automatically. 4 SIGNAL indicator A channel's SIGNAL indicator lights up when its output exceeds a certain amount (2V rms on the XM4180/ XM4080, 4V rms on the XH200. ) * The illustration shows model XM4180/XM4080. 6 XM4180/XM4080/XH200 Owner's Manual 4 Rear Panel (XM4180/XM4080) 13 2 4 6 13 2 4 5 6 7 8 * The illustration shows model XM4180. 1 XLR inputs connectors These balanced XLR-3-31 type connectors are used to connect input signals. The pins are wired as shown below (IEC 60268). BRIDGED mode In BRIDGED mode, channels A and B operate simultaneously, functioning as a single mono amplifier. (The same applies to the C and D. ) Note: When in PARALLEL and BRIDGED modes, input terminals A-B and C-D are shorted automatically. Make sure not to input an audio signal to an inactive input terminal. Hot Ground Cold * In bridged mode, only the first channel in the pair is active; i. e. , channel A of pair A/B, and channel C of pair C/D. Make sure not to input an audio signal to an inactive input terminal. 5 MONITOR/REMOTE terminals This terminal is used to connect the external device for monitoring or remote control. Refer to "MONITOR/ REMOTE PIN layout" on page 14. 2 Euroblock connectors These balanced Euroblock connectors are used to connect input signals. 6 SPEAKERS terminals These 5-way binding posts are used to connect speakers. 3 HPF switches These switches are used to turn on and off the HPF (High Pass Filter) for channels A-B or C-D. When this is set to 20Hz or 55Hz, frequencies below the respective settings are filtered using a 12 dB/octave high pass filter. 7 GND terminal If you are having a problem with hum or noise, use this terminal to connect to ground (earth) or to connect to the chassis of a mixer, preamp, or other device in your system. 4 MODE switch STEREO mode 8 AC IN Connect one plug of the included AC cable to this inlet. Connect the other plug of the AC cable to an AC outlet that meets the power supply conditions printed on the label at the top of the unit. In STEREO mode, channels A , B, C and D are completely independent. PARALLEL mode In PARALLEL mode, the channel A input signal is sent both to the channel A power amp and the channel B power amp. In this case, loads are automatically connected between the A and B input terminals. (The same applies to the C and D input terminals. ) By sending the signal from channels A/B to C/D you can use the unit as a four-channel mono amplifier. XM4180/XM4080/XH200 Owner's Manual 7 5 Using as a four-channel mono amplifier with a mono input (XM4180/XM4080) By connecting input terminals B and C with a proper cable, and setting both mode switches for A/B and C/D to PARALLEL, you can use the unit as a four-channel mono amplifier. The volume controls on the front panel (A to D) let you control the volume of each channel independently. Note In this case, the loads for A and B or C and D are connected in the amplifier. Make sure not to input any signal to the D terminal. Input signal Speaker Speaker + ­ + ­ + ­ + ­ Connect B and C Speaker Speaker * The illustration shows model XM4180. Using as a two-channel amplifier with a mono input for high-power applications (XM4180/XM4080) By connecting input terminals B and C with a proper cable, and setting both mode switches for A/B and C/D to BRIDGE, you can use the unit as a two-channel high-power mono amplifier. Note In this case, the loads for A and B or C and D are connected in the amplifier. Make sure not to input any signal to the D terminal. Input signal Speaker + ­ + ­ Connect B and C Speaker * The illustration shows model XM4180. 8 XM4180/XM4080/XH200 Owner's Manual 6 Speaker connections (XM4180/XM4080) Speakers can be connected to the amplifier in two ways, as shown below. Note that speaker impedance will vary according to the connection method and the number of speakers. Please be sure that your speaker's impedance is not less than the relevant minimum value indicated below. Connection configurations for STEREO and PARALLEL modes Connection configurations for BRIDGED mode or ­ + + ­ ­ + Minimum speaker impedance: 4 Minimum speaker impedance: 4 Minimum speaker impedance: 8 * The illustration shows model XM4180. When connecting high-impedance speakers in parallel (XM4180 only) XM4180 enables you to connect in parallel fashion multiple high-impedance speakers that support 70V line output. The number of speakers that can be connected varies depending on the rated input of the speakers. The XM4180 can be connected to speakers with a total rated input of up to 300 W. [. . . ] Para detalles sobre productos, contacte su tienda Yamaha más cercana o el distribuidor autorizado que se lista debajo. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 POLAND Yamaha Music Europe GmbH Branch Sp. z o. o. 17 Stycznia 56, PL-02-146 Warszawa, Poland Tel: 022-868-07-57 ASIA THE PEOPLE'S REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co. , Ltd. 2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu, Shanghai, China Tel: 021-6247-2211 U. S. A. Yamaha Corporation of America 6600 Orangethorpe Ave. , Buena Park, Calif. [. . . ]