User manual YAMAHA XVS650A-2004

[. . . ] OWNER'S MANUAL XVS650A 5SC-28199-E1 EAU26941 DECLARATION of CONFORMITY We Company: MORIC CO. , LTD. Address: 1450-6 Mori Mori-Machi Shuchi-gun Shizuoka 437-0292 Japan Hereby declare that the product: Kind of equipment: IMMOBILIZER Type-designation: 5SL-00, 5VS-00, 5VX-00, 3HT-00, 5UX-00, 5UX-10, 5KS-00 and 5KS-10 is in compliance with following norm(s) or documents: R&TTE Directive(1999/5/EC) EN300 330-2 v1. 1. 1(2001-6), EN60950(2000) Two or Three-Wheel Motor Vehicles Directive(97/24/EC: Chapter 8, EMC) Place of issue: Shizuoka, Japan Date of issue: Aug. 1st 2002 Kazuji Kawai representative name and signature INTRODUCTION EAU10100 Welcome to the Yamaha world of motorcycling!As the owner of the XVS650A, you are benefiting from Yamaha's vast experience and newest technology regarding the design and manufacture of high-quality products, which have earned Yamaha a reputation for dependability. [. . . ] In addition, the oil must be changed and the oil filter element replaced at the intervals specified in the periodic maintenance and lubrication chart. Place the vehicle on a level surface and hold it in an upright position. NOTE: Make sure that the vehicle is positioned straight up when checking the oil level. A slight tilt to the side can result in a false reading. Start the engine, warm it up for several minutes, and then turn it off. Wait a few minutes until the oil settles, and then check the oil level through the check window located at the bottom-left side of the crankcase. To install a spark plug 1. Measure the spark plug gap with a wire thickness gauge and, if necessary, adjust the gap to specification. 6 NOTE: If a torque wrench is not available when installing a spark plug, a good estimate of the correct torque is 1/4­1/2 turn past finger tight. However, the spark plug should be tightened to the specified torque as soon as possible. Spark plug gap Spark plug gap: 0. 8­0. 9 mm (0. 031­0. 035 in) 6-7 PERIODIC MAINTENANCE AND MINOR REPAIR NOTE: The engine oil should be between the minimum and maximum level marks. Place an oil pan under the engine to collect the used oil. Remove the engine oil filler cap and drain bolt to drain the oil from the crankcase. 1. 4. Engine oil level check window Maximum level mark Minimum level mark Engine oil filler cap 1. If the engine oil is at or below the minimum level mark, add sufficient oil of the recommended type to raise it to the correct level. To change the engine oil (with or without oil filter element replacement) 1. Start the engine, warm it up for several minutes, and then turn it off. NOTE: Skip steps 4­7 if the oil filter element is not being replaced. Remove the outer and inner oil filter element covers by removing the bolts. 1. Remove the oil filter element and O-ring. 6-8 PERIODIC MAINTENANCE AND MINOR REPAIR Tightening torque: Engine oil drain bolt: 43 Nm (4. 3 m·kgf, 31 ft·lbf) G Make sure that no foreign material enters the crankcase. 9. Add the specified amount of the recommended oil, and then install and tighten the oil filler cap. Recommended engine oil: See page 8-1. Oil quantity: Without oil filter element replacement: 2. 60 L (2. 75 US qt) (2. 29 Imp. qt) With oil filter element replacement: 2. 80 L (2. 96 US qt) (2. 46 Imp. qt) ECA11620 1. Start the engine, and then let it idle for several minutes while checking it for oil leakage. If oil is leaking, immediately turn the engine off and check for the cause. [. . . ] 6-1 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-34 Troubleshooting chart . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-35 Turn signal indicator light . . . . . . . . . . . . . . . . . . . . . . . . 3-3 D Dimmer switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6 M Main switch/steering lock. . . . . . . . . . . . . . . . . . . . . . . . [. . . ]