User manual YAMAHA YPDR

[. . . ] IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Failure to follow instructions could void your FCC authorization to use this product in the USA. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class "B" digital devices. [. . . ] It adds the airiness, which is found when a microphone is placed in front of the guitar's sound hole. The Mic Simulator is useful when your guitar is connected directly to a mixer or recorder via a line, or when listened to through a pair of headphones for practice, etc. The AG-Stomp provides the eight different Mic Simulator settings described below. The Mic Simulator creates a stereo image by simulating two microphones positioned in front of the guitar but "aimed" at dif ferent angles toward the guitar. Use the MIC TYPE Select Switch to try out some of the different microphone simulation types. The BLEND knob is used to adjust the volume balance between the signal after it has passed through the Mic Simulator (MIC tone) and the signal before it has passed through the Mic Simulator (DIRECT tone). Rotate the knob fully to the left to hear only the DIRECT tone. Rotate the knob fully to the right to hear only the MIC tone. Also, pressing the [SHIFT] button to enter the SHIFT mode (the SHIFT lamp flashes) lets you use the BLEND (stereo) knob to adjust spaciousness of the sound produced by the Mic Simulator's two microphones. Press the [SHIFT] button again to exit the SHIFT mode and the lamp will turn off. * In the SHIFT mode, if a knob is not rotated after five seconds, the mode will be exited automatically. Simulates microphones positioned close to the guitar. Simulates microphones positioned far from the guitar. Microphone Microphone Microphone Microphone Microphone Microphone Microphone Microphone MIC TYPE Select Switch Position CONDENSER 1 CONDENSER 2 DYNAMIC 1 DYNAMIC 2 TUBE 1 TUBE 2 NYLON STR 1 NYLON STR 2 Display Description of the Simulation Simulates the characteristics associated with a condenser mic positioned close to the acoustic guitar. Simulates the characteristics associated with a condenser mic positioned far from the acoustic guitar. If you want to keep the changes you made to those settings, use the Store Operation described on page 19. Frequency 16 Using the AG-Stomp I Selecting Patches The AG-Stomp holds a total of 60 patch programs (patch) in its internal memory. The 60 patches are divided into two areas, ten banks and three patches. · AREA There are two areas, the USER AREA and the PRESET AREA. Data in the USER AREA (30 patches) can be freely rewritten using the STORE operation. Data in the PRESET AREA (30 patches) can be edited but the contents can not be rewritten to PRESET AREA memory. When a USER AREA patch is selected, a "U" will appear in the display's hundred's digit (U01- G Use the [UP]/[DOWN] buttons on the panel. · Each time the [UP] button is pressed, the next greater patch number is selected. U01 U02 U03 U11 U12 U13. . . . . U91 U92 U93 P01 P02. . . . . P93 U01 (returns to the top). . . Each time the [DOWN] button is pressed, the next lesser patch number is selected. · Holding the [UP] button continuously increases the bank number by one. U93). When a PRESET AREA patch is selected, a "P" will appear in the display's hundred's digit (P01- U01 U11 U21 U31. . . . . U91 P01 P11. . . . . P91 U01 (returns to the top). . . Holding the [DOWN] button continuously decreases the bank number by one. · Simultaneously press the [UP] and [DOWN] button switches between the USER AREA and PRESET AREA. P93). * When the AG-Stomp is shipped, both the PRESET AREA and USER AREA contain the same patch data. (Refer to the supplemental [Patch List]). · BANK The 30 patches in each area are divided into ten banks (0-9). · PATCH Each Bank contains three patches (1-3). [. . . ] · PrG : When patches are changed, the Feedback Reduction's parameters and settings will be changed to those that are stored with the patch's data. 27 Error Messages If an error occurs during operation, one of the following error message numbers will appear in the display. Stop operation of the AG-Stomp and follow one of the solutions described below. E1: MIDI Receive Buffer Full CAUSE: Too much MIDI data is being received and the buffer is full SOLUTION: Try reducing the amount of data being sent, or break the data into smaller blocks. E2: Communication Error CAUSE: An abnormality is detected during MIDI communications. and try again. E3: Bulk Receive Check Sum Error CAUSE: The check sum does not match the received MIDI bulk dump data. SOLUTION: Check all connections and transmitted data, and try again. E4: Bulk Receive Data Abnormality CAUSE: An abnormality is detected while receiving the bulk dump. [. . . ]