User manual YAMAHA YS100E

[. . . ] Product performance and/or safety standards may be diminished. Claims filed under the expressed warranty may be denied if the unit is/has been modified. Implied warranties may also be affected. SPECIFICATIONS SUBJECT TO CHANGE: The information contained in this manual is believed to be correct at the time of printing. [. . . ] Note: You cannot use Internet Direct Connection on the piano listed above. 7 Chapter 2 Getting Started Replacing the Existing Control Unit with the Disklavier Control Unit Connect the Disklavier control unit to your piano, replacing with the existing control unit. 4 6 7 Tighten Disklavier control unit 5 Conversion cable (supplied) Connect monitor speakers. See page 12. AC adaptor (PJP-PS02/PJP-PS04) (supplied) Power cable (supplied) . Control cable Your piano 3 2 8 Tighten Loosen Cautions · Use the Yamaha PJP-PS02/PJP-PS04 adaptor, or an equivalent recommended by Yamaha. Use of other AC adaptors may result in damage, overheating, or fire. · Do not stretch the cable or bend its ends. · Do not attempt to use the cable if it is stretched or if the ends of the cable have been bent. Attempting to do so may cause interruptions to the power supply. · Always turn off the main unit power before disconnecting the AC adaptor. · When you wish to move the Disklavier control unit, unplug the AC adaptor from the AC wall outlet and disconnect if from the DC-IN 12V connector on the rear panel of the Disklavier control unit before proceeding. · Unplug the AC adaptor from the AC wall outlet if you do not intend to use the instrument for an extended period of time. 8 Chapter Getting Started 2 1 2 Turn off your piano, and disconnect the power cable from the AC wall outlet. Note: The location of the TO CONTROL CABLE FOR PIANO connector varies depending on the piano model. Important: Please keep the disconnected control unit for future maintenance. English Disconnect the control cable from the TO CONTROL CABLE FOR PIANO connector on the rear panel of your control unit. Loosen the two screws attached to the connector by the screwdriver. 3 Connect the supplied conversion cable to the control cable disconnected in step 2. Tighten the two screws attached to the connector by the screwdriver. 4 Connect the supplied conversion cable to the TO PIANO connector on the rear panel of the Disklavier control unit. Tighten the two screws attached to the connector by the screwdriver. 5 6 7 8 Connect monitor speakers to the OUTPUT jacks on the rear panel of the Disklavier control unit. See Chapter 2 "Getting Started ­ Connecting Monitor Speakers" on page 12. Connect the supplied AC adaptor to the DC-IN 12V connector on the rear panel of the Disklavier control unit. Connect the supplied power cable to the AC adaptor. Connect the power cable extended from your piano and the AC adaptor to the AC wall outlet. The connection completed. Turn on the Disklavier control unit, and set the piano type. See Chapter 2 "Getting Started ­ Setting the Type of Your Piano" on page 15. 9 Chapter 2 Getting Started Connecting the Disklavier Control Unit with the MIDI Cables Connect the Disklavier control unit to your piano using the MIDI cables. 2, 3 2, 3 4 Your control unit . Connect monitor speakers. This section provides notes on handling the remote control. Installing Batteries in the Remote Control Before the remote control can be used, the two batteries supplied with the Disklavier control unit must be installed. Remove the battery cover from the rear of the remote control, install the batteries, and then replace the cover. English A diagram inside the battery compartment shows which way the batteries should be installed. Make sure you insert them correctly. Battery Replacement When the remote control fails to work from a distance, replace the batteries. · Replacement batteries should be UM-3, AA, R6P, or LR6 type. · Do not use new and old dry batteries together. · Do not use different types of batteries (alkaline and manganese batteries, batteries made by different manufacturers or different battery products made by the same manufacturer) together. · Remove spent batteries immediately from the remote control. Otherwise, batteries will overdischarge, causing them to leak electrolyte or burst which in turn may result in damage to nearby objects or in burns, injury or other bodily harm. · Dispose of batteries in accordance with the applicable regulations and ordinances. · If the remote control is not to be used for a prolonged period of time, remove the batteries to prevent possible damage by battery leakage. · If the batteries have leaked, dispose of them immediately. [. . . ] Option SAVE NEW Description The song is saved at its new tempo under the current song number. The song is saved at its new tempo under a new song number. The original song is kept under the previous song number. CANCEL The song with a new tempo is discarded. The original song is kept under the previous song number. 7 Press [ ] and [ ] to select an option, then press [ENTER]. To change the tempo again or to reset the original tempo, repeat steps 1 to 6. 67 Chapter 8 1 Advanced Piano Playing Playing the Disklavier along with the Internal Metronome [METRONOME] The internal metronome helps you playing along the meter (beat) and the tempo you set. [. . . ]