User manual YAMAHA YSP-500

[. . . ] G YSP-500 Digital Sound ProjectorTM Système Acoustique Numérique OWNER'S MANUAL MODE D'EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING GEBRUIKSAANWIJZING CAUTION: READ THIS BEFORE OPERATING THIS UNIT. Caution: Read this before operating this unit. 1 2 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. Install this sound system in a well ventilated, cool, dry, clean place with at least 5 cm (2 in) of space above (or below) this unit ­ away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. [. . . ] Use this feature to redirect audio signals if the sound coming from the front left and right channels seems unnatural, such as when your listening position is not the center of your listening room. You can only adjust this parameter when 3 Beam or 5 Beam is selected as the beam mode (see page 44). Choices: ON, OFF Setting range: 0% to 95% Initial setting: 0% C)IMAGE LOCATION . OFF L C [ ]/[ ]:Up/Down [ ]/[ ]:Sel [ENTER]:Return LEFT (Left) Adjusts audio signals toward the left. The higher the percentage, the louder the output from the center. Without adjustment With the front left channel adjusted d)TREBLE GAIN + . Front L;;;;;;;;0dB -----Front R;;;;;;;;0dB -----Center;;;;;;;;;0dB -----Surround L;;;;;0dB -----Surround R;;;;;0dB -----[ ]/[ ]:Up/Down [ ]/[ ]:Sel [ENTER]:Return RIGHT (Right) Adjusts audio signals toward the right. The higher the percentage, the louder the output from the center. Without adjustment With the front right channel adjusted p p Choices: ­12. 0 dB to +12. 0 dB Initial setting: 0 dB · Front L adjusts the high-frequency output level of the front left channel. · Front R adjusts the high-frequency output level of the front right channel. · Center adjusts the high-frequency output level of the center channel. · Surround L adjusts the high-frequency output level of the surround left channel. · Surround R adjusts the high-frequency output level of the surround right channel. )ON R LEFT;;;;;;;;;;;0% RIGHT;;;;;;;;;;0% p p p p p p p ADVANCED OPERATION English 61 En MANUAL SETUP SOUND MENU Use to manually adjust the various parameters related to the sound output. SET MENU MANUAL SETUP SOUND MENU 1)SOUND MENU . A)TONE CONTROL B)SUBWOOFER SET C)MUTE LEVEL D)AUDIO DELAY E)DD/DTS Dynamic Range F)TruBass [ ]/[ ]:Up/Down [ENTER]:Enter BASS OUT (Bass out) Low-frequency (bass) signals can be directed to the subwoofer and/or the front left and right channels. This setting also determines the routing of LFE (low-frequency effect) signals found in Dolby Digital or DTS sources. Choices: SWFR (Subwoofer), FRONT · Select SWFR if you connect a subwoofer. LFE and low-frequency signals from other channels are directed to the subwoofer. · Select FRONT if you do not use a subwoofer. LFE and low-frequency signals from other channels are directed to the front left and right channels. CROSS OVER (Crossover) When BASS OUT is set to SWFR, you can use this feature to select a crossover (cutoff) frequency for all lowfrequency signals. All frequencies below the selected frequency will be sent to the subwoofer position. Choices: 100Hz, 120Hz, 150Hz LFE LEVEL (Low-frequency effect level) Select to adjust the output level of the LFE (low-frequency effect) channel according to the capacity of your subwoofer. The LFE channel carries low-frequency special effects which are only added to certain scenes. [. . . ] p p, p p . pp p p DVD-pp p . DVD-pp p, p , DVD-pp. p 1 p DVD-pp p p. p , p¤, , . p 40° - 50° . p. 1 ( p p p) 2 --p (Op p YSP-500 p) 3 ( p p p p) p, pp, p, pp, ANALOG AUDIO VIDEO OUTPUT INPUT L 1 p p p p p p p OPTICAL AUDIO OUTPUT 1. p p , p, pp p . COAXIAL AUDIO OUTPUT 4 p ( p DVD p p) p p p p p p p 40° - 50° R 2 2. [. . . ]