User manual YAMAHA YST-MSW10

[. . . ] WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK. DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. Please record the serial number of this unit in the space below. Model: Serial No. : The serial number is located on the rear of the unit. [. . . ] 12 Cleaning ­ The unit should be cleaned only as recommended by the manufacturer. 13 Nonuse Periods ­ The power cord of the unit should be unplugged from the outlet when left unused for a long period of time. 14 Object and Liquid Entry ­ Care should be taken so that objects do not fall into and liquids are not spilled into the inside of the unit. 15 Damage Requiring Service ­ The unit should be serviced by qualified service personnel when: A. The power-supply cord or the plug has been damaged; or B. Objects have fallen, or liquid has been spilled into the unit; or C. The unit has been exposed to rain; or D. The unit does not appear to operate normally or exhibits a marked change in performance; or E. The unit has been dropped, or the cabinet damaged. 16 Servicing ­ The user should not attempt to service the unit beyond those means described in the operating instructions. All other servicing should be referred to qualified service personnel. 17 Power Lines ­ An outdoor antenna should be located away from power lines. 18 Grounding or Polarization ­ Precautions should be taken so that the grounding or polarization is not defeated. 6 9 10 Power Sources ­ The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the unit. i System Example / Ejemplo del sistema Personal Computer Portable CD Player or Speaker System with Connecter for Subwoofer POWER Personal Computer Portable CD Player or YST-MSW10 ACTIVE SERVO PROCESSING SUBWOOFER SYSTEM YST-MSW10 Actve Servo Technology LINE 1 1 INPUT POWER HIGH CUT HIGH LOW VOLUME IN 2 PRESENCE VOLUME Actve Servo Technology TO LEFT SPEAKER OUTPUT (ADJ. VOL) OUT DC 9V YST-M10 Speaker System with Built-in Amp. YST-MSW10 ACTIVE SERVO PROCESSING SUBWOOFER SYSTEM YST-MSW10 Actve Servo Technology LINE 1 STEREO INPUT POWER HIGH CUT HIGH LOW VOLUME IN OUTPUT to DC 14V To Left Speaker OUT YST-M10 POWERED MONITOR SPEAKER Actve Servo Technology POWER PRESENCE VOLUME SER NO. 1 Front Panel & Rear Panel / Panel delantero y Panel trasero ACTIVE SERVO PROCESSING SUBWOOFER SYSTEM YST-MSW10 Active Servo Technology LINE 2 LINE 1 L IN 3 R OUT 1 2 4 5 POWER HIGH CUT HIGH LOW VOLUME 6 MADE IN MALAYSIA V844750-1 UC 2 Thank you for purchasing a Yamaha YST-MSW10 Subwoofer System. Yamaha's Active Servo Technology offers exceptional high performance. Cautions Please read the following operating precautions before use: · When disconnecting the power cord from an AC receptacle, hold and pull the plug, not the cord. · If the YST-MSW10 is not going to be used for a while, disconnect it from the AC receptacle. · Since this unit has a built-in power amplifier, heat will radiate from the rear panel. Therefore, place the unit at least 10 cm (4 inches) away from the wall. Also, do not position with the rear panel facing down on the floor or other surface. [. . . ] In this case, move it away a little. Connections Refer to page 1 for system connections. Rear Panel (Refer to page 2) 1 LINE 1 IN: This 3. 5 mm stereo jack connection is for inputting line-level signals to the YST-MSW10. 2 LINE 1 OUT: This connection can be used to feed the input signal to other equipment. 3 LINE 2: These RCA-pin jacks are for inputting speaker level signals to the YST-MSW10. They can be connected directly to the speaker outputs of a stereo amplifier. 3 Front Panel (Refer to page 2) 4 POWER Switch and Indicator: Press to power on the YST-MSW10; the power indicator will light up. Before powering on and off, turn down the VOLUME control. Type Amplifier output High-Cut Filter Pressure Level Capacity Frequency response Speaker unit Power supply Power consumption Active Servo Processing Subwoofer System 25 W/4 (THD 10%, 100 Hz) Low, High 98 dB (max. ) 8. 0 l 35 to 250 Hz (­10dB) 6. 3" (16 cm) cone woofer, magnetic shielding AC 120 V, 60 Hz 25 W 5. 5 kg (12. 1 lbs) Mini plug cable × 1 RCA pin to Mini plug adaptor × 1 1/4" Phone to Mini plug adaptor × 1 5 HIGH CUT Switch: This switch selects the high-cut filter frequency: Set it to either LOW or HIGH. 6 VOLUME Control: Use this control to set the volume level. Turn it clockwise to increase the volume, and counterclockwise to reduce it. Auto Power On/Off Function When powered on, if no input signal is received after 5­10 minutes, the power is switched off automatically. [. . . ]