User manual YAMAHA YST-SW15002

[. . . ] UB YST -SW 500 1 Subwoofer System OWNER'S MANUAL I IMPORTANT SAFETY INSTRUCTIONS 1 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN Read these instructions. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. [. . . ] Caution Do not let the bare speaker wires touch each other as this could damage the subwoofer or the amplifier, or both of them. How to Connect: Red: positive (+) Black: negative (­) <U. S. A. , Canada, Australia and Korean models only> Banana Plug connections are also possible. 1 1 Loosen the knob. 10 mm (3/8") insulation from the speaker wires. ] 3 Tighten the knob and secure the wire. 2 2 1 3 1Tighten the terminal knob. 2Simply insert the Banana Plug connector into the terminal. E-7 Connecting to H. P. F. OUTPUT terminals for connections with the amplifier will improve sound quality of your speaker system. (High-Pass Filter) OUTPUT terminals of the subwoofer cut off frequencies below the selected frequency point from the input signals, and output high frequencies only. By connecting this terminal with the MAIN IN terminals of the amplifier, the main speakers reproduce high frequencies only. This will make the whole sound quality clear by preventing sound muddying between the main speakers and the subwoofer. * This connection can be made if your amplifier has PRE OUT and MAIN IN terminals or you are using separate amplifiers (pre-amplifier and main amplifier). To connect one unit only Right main speaker Left main speaker H. P. F. OUTPUT LFE NORMAL /MONO OUTPUT TO SPEAKERS 80Hz 100Hz Subwoofer REMOTE AUTO STANDBY H. P. F. OUTPUT LFE NORMAL /MONO GND INPUT 3 INPUT 2 FROM AMPLIFIER OUTPUT TO SPEAKERS OUTPUT INPUT HIGH LOW OFF 80Hz 100Hz GND INPUT 3 INPUT 2 FROM AMPLIFIER INPUT 1 INPUT 1 Audio pin cable (not included) POWER ON OFF AC IN Audio pin cable (not included) PRE OUT MAIN IN Amplifier E-8 English To connect two units Right main speaker Left main speaker H. P. F. OUTPUT LFE NORMAL /MONO OUTPUT TO SPEAKERS H. P. F. OUTPUT LFE NORMAL /MONO OUTPUT TO SPEAKERS 80Hz 100Hz 80Hz 100Hz GND INPUT 3 INPUT 2 FROM AMPLIFIER GND INPUT 3 INPUT 2 FROM AMPLIFIER INPUT 1 INPUT 1 Right subwoofer REMOTE AUTO STANDBY H. P. F. OUTPUT LFE NORMAL /MONO Left subwoofer REMOTE AUTO STANDBY H. P. F. OUTPUT LFE NORMAL /MONO OUTPUT TO SPEAKERS OUTPUT TO SPEAKERS OUTPUT INPUT HIGH LOW OFF 80Hz 100Hz OUTPUT INPUT HIGH LOW OFF 80Hz 100Hz GND INPUT 3 INPUT 2 FROM AMPLIFIER GND INPUT 3 INPUT 2 FROM AMPLIFIER INPUT 1 INPUT 1 POWER ON POWER ON OFF AC IN AC IN OFF PRE OUT MAIN IN Switching the H. P. F. OUTPUT switch After the connection is made, select the desired frequency point (80 Hz or 100 Hz) with the H. P. F. (Normally, it is recommended to select the frequency point nearer to the main speakers' minimum reproduceable frequency. ) Frequencies higher than the selected frequency are output from the H. P. F. OUTPUT terminals. H. P. F. OUTPUT 80Hz 100Hz GND Mono pin cables (not included) Amplifier E-9 Ground connection If there is a humming noise when using the subwoofer connected to the speaker terminals, connect the subwoofer and the receiver/amplifier with the grounding cable as shown in Illustration A. * If there is no ground terminal (GND) on the receiver/amplifier side, connect the cable to a screw that fastens the top cover of the receiver/amplifier to the rear panel as shown in Illustration B. Insert Tighten Grounding cable Subwoofer REMOTE AUTO STANDBY H. P. F. OUTPUT LFE NORMAL /MONO OUTPUT TO SPEAKERS OUTPUT INPUT HIGH LOW OFF 80Hz 100Hz GND INPUT 3 INPUT 2 FROM AMPLIFIER INPUT 1 Metal part DIGITAL OUTPUT MD/ TAPE IN (PLAY) CD-R MD/TAPE OUT (REC) AUDIO R L R AUDIO SIGNAL R L 2 PHONO R AC IN POWER TUNER ON PRE OUT OPTICAL CD IN (PLAY) CD-R CD-R OUT (REC) DVD SIGNAL GND D-TV /LD PHONO CD 3 L IN (PLAY) TAPE OFF MAIN IN 4 3 OUT (REC) IN (PLAY) MD OPTICAL COAXIAL CD RS232C MAIN 1 R CD/DVD L 4 OUT (REC) AUX CBL /SAT SURROUND LD RF (AC-3) COAXIAL: SELECT BY SETMENU DIGITAL INPUT CENTER SUB WOOFER 6CH INPUT Receiver/amplifier E-10 English Connecting the AC power cable POWER ON OFF AC IN <U. S. A. , Canada, Europe and Korean models> When all connections are completed, plug the included power cable into the AC IN socket of the subwoofer, and then plug in the power cable to the wall outlet. Notes Never connect any power cable other than the included one to the subwoofer. Otherwise, it may result in causing fire or an electrical shock. Do not connect the included power cable to any other unit than this subwoofer. (U. S. A. model) To AC outlet POWER ON OFF AC IN <U. K. and Australia models> Plug in the subwoofer to the wall outlet. (U. K. model) To AC outlet NOTES ABOUT THE REMOTE CONTROL Battery installation Remote control operation range 3 2 1 Remote control sensor Within approximately 6 m (20 feet) Battery replacement If you find that the remote control must be used closer to the main unit, the batteries are weak. Notes Use only AA, R6, UM-3 batteries for replacement. (See the illustration inside the battery compartment. ) Remove the batteries if the remote control will not be used for an extended period of time. If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. [. . . ] Turn down the volume on the amplifier etc. connected to the subwoofer or cut off the power to other unused equipment. Change position of the main unit. The subwoofer turns into the standby mode unexpectedly. The subwoofer turns on unexpectedly. The level of input signal is too low. [. . . ]