User manual YAMAHA YST-SW80

[. . . ] YST-SW 50/80 1 Active Servo Processing Subwoofer System Built-in 100W Power Amplifier (YST-SW150) Built-in 70W Power Amplifier (YST-SW80) 2 Way Selectability for Connections High Frequency Cut-off Point (HIGH CUT) Control PHASE Switch AUTO POWER ON/OFF Switch Thank you for selecting this YAMAHA Subwoofer System. Active Servo Technology CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN OWNER'S MANUAL IMPORTANT!Please record the serial number of this unit in the space below. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CONTENTS Safety Instructions . . . . . . . . . . . . . . . . . . . 2 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Placement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Controls and Their Functions . . . . . . . 8 Adjusting Volume . . . . . . . . . . . . . . . . . . . . . 9 Active Servo Technology . . . . . . . . 11 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . 12 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 12 · Explanation of Graphical Symbols Model: Serial No. : The serial number is located on the rear of the unit. Retain this Owner's Manual in a safe place for future reference. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. SAFETY INSTRUCTIONS 1 2 3 4 5 Read Instructions ­ All the safety and operating instructions should be read before the unit is operated. [. . . ] (Refer to page 11 for details on Active Servo Technology. ) This unit does not only enhance bass frequency response of sound output in your audio system, but, by reproducing the bass frequencies, the subwoofer permits your existing amplifier and speakers to operate under less strenuous conditions, improving overall system performance. · · · This unit can be added easily to your existing audio system by connecting to either the speaker terminals or the line output (pin jack) terminals of the amplifier. For the effective use of this unit, this unit's super-bass sound must be matched to the sounds of your main speakers. Therefore, this unit employs a continuously variable high frequency cut-off point (HIGH CUT) control. Moreover, the PHASE switch allows you to select the best sound quality for various listening conditions. A newly employed AUTO POWER ON/OFF switch saves you the trouble of pressing the POWER switch when turning the power on and off. PLACEMENT A B C ( : subwoofer, : main speaker) One subwoofer will have a good effect on your audio system, however, the use of two subwoofers is recommended to obtain more presence. Note There may be a case that you cannot obtain enough superbass sounds from this unit when listening at the middle of the room. This is because "standing waves" have developed between two parallel walls and the bass sounds are being canceled. In such a case, face the unit obliquely to the wall. It also may be necessary to break up the parallel surfaces by placing bookshelves etc. along the walls. If using one subwoofer, it is recommended to place it on the outside of either the right or the left main speaker. A . ) If using two subwoofers, it is recommended to place them on the outside of each main speaker. C is also possible, however, if the subwoofer system is placed directly facing the wall, the bass effect may die because the sound from it and the sound reflected by the wall may cancel. To prevent this, face the subwoofer system obliquely to the wall as shown in fig. A or B . 4 CONNECTIONS · Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other components to which connections are being made. · When making connections between this unit and other components, be sure all connections are made correctly and consistently, that is to say L (left) to L, R (right) to R, "+" to "+" and "­" to "­". · This unit can be connected to either the speaker terminals or the line output (pin jack) terminals of the amplifier. Choose one of the ways shown below according to your audio system. · Amplifier line output terminals are generally labeled PRE OUT or SUBWOOFER OUT. * For PRE OUT terminal connection, the amplifier must possess at least two sets of PRE OUT terminals. With some amplifiers with only one set of PRE OUT terminals, connection can result in no sound from the main left and right speakers. In this case, select the method of connecting to the speaker terminals. · To connect with a YAMAHA DSP amplifier, connect the LOW PASS (or SUBWOOFER etc. ) terminal on the rear of the DSP amplifier to either the left (L) or right (R) INPUT 2 terminal. If using one unit Left speaker This unit OUTPUT TO SPEAKERS INPUT2 AUTO POWER PHASE ON OFF NOM REV OUTPUT TO SPEAKERS INPUT2 AUTO POWER PHASE Right speaker FROM AMPLIFIER INPUT1 ON OFF NOM REV FROM AMPLIFIER INPUT1 To AC outlet <YAMAHA DSP amplifier> LOW PASS Pin plug cords Amplifier <Amplifier> PRE OUT If using two units Left speaker OUTPUT TO SPEAKERS INPUT2 AUTO POWER PHASE OUTPUT TO SPEAKERS INPUT2 AUTO POWER PHASE Right speaker ON OFF NOM REV ON OFF NOM REV FROM AMPLIFIER INPUT1 FROM AMPLIFIER INPUT1 Pin plug cords This unit OUTPUT TO SPEAKERS INPUT2 AUTO POWER PHASE ON OFF NOM REV This unit OUTPUT TO SPEAKERS INPUT2 AUTO POWER PHASE ON OFF NOM REV FROM AMPLIFIER INPUT1 FROM AMPLIFIER INPUT1 PRE OUT Amplifier To AC outlet To AC outlet Notes · When connected to line output terminals of the amplifier, other speakers should not be connected to the OUTPUT terminals on the rear panel of this unit. [. . . ] The features described above, then, are combined to be the fundamental structure of the Active Servo Technology. Highamplitude bass sound Cabinet Port Air woofer (Helmholtz resonator) Active Servo Processing Amplifier Signals Negative-impedance output drive Signals of low amplitude 11 TROUBLESHOOTING If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for help. SYMPTOM Power is not supplied even though the POWER switch is ON. CAUSE The power plug is not securely connected. Speaker cables are not connected securely. [. . . ]