User manual YAMAHA YST-SW90

[. . . ] BGRT English YST -SW1 60/90 Active Servo Processing Subwoofer System Caisson de grave avec asservissement actif OWNER'S MANUAL MODE D'EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING MANUALE DI ISTRUZIONI MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZING 1 Thank you for selecting this YAMAHA subwoofer system. CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. 1. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 15. Secure placement or installation is the owner's responsibility. [. . . ] Do not let the core of the speaker wires touch each other and do not let them touch the metal parts of this unit as this could damage this unit, your amplifier and/or speakers. * Banana Plug connections are also possible (except for U. K. Simply insert the Banana Plug connector into the corresponding terminal. How to Connect: Red: positive (+) Black: negative (­) 1 Unscrew the knob. 5 mm (1/4") insulation from the speaker wires. ] 3 Tighten the knob to secure the wire firmly. 5 CONNECTING TO LINE OUTPUT (PIN JACK) TERMINALS OF THE AMPLIFIER · Connect the main speakers to the speaker output terminals of the amplifier. · Amplifier line output terminals are generally labeled PRE OUT or SUBWOOFER OUT. · To connect with a YAMAHA DSP amplifier, connect the SUBWOOFER (or LOW PASS etc. ) terminal on the rear of the DSP amplifier to either the left (L) or right (R) INPUT 2 terminal. Using one unit Left speaker This unit OUTPUT TO SPEAKERS INPUT2 AUTO STANDBY PHASE BASS OUTPUT TO SPEAKERS INPUT2 AUTO STANDBY PHASE BASS Right speaker LOW HIGH NOM REV MOVIE MUSIC FROM AMPLIFIER INPUT1 OFF LOW HIGH NOM REV MOVIE MUSIC FROM AMPLIFIER INPUT1 POWER ON OFF OFF To AC outlet <YAMAHA DSP amplifier> SUBWOOFER Pin plug cords Amplifier <Amplifier> PRE OUT Using two units Left speaker OUTPUT TO SPEAKERS INPUT2 AUTO STANDBY PHASE BASS OUTPUT TO SPEAKERS INPUT2 AUTO STANDBY PHASE BASS Right speaker LOW HIGH NOM REV MOVIE MUSIC LOW HIGH NOM REV MOVIE MUSIC FROM AMPLIFIER INPUT1 OFF FROM AMPLIFIER INPUT1 OFF This unit OUTPUT TO SPEAKERS INPUT2 AUTO STANDBY PHASE BASS This unit OUTPUT TO SPEAKERS INPUT2 AUTO STANDBY PHASE BASS Pin plug cords LOW HIGH NOM REV MOVIE MUSIC LOW HIGH NOM REV MOVIE MUSIC FROM AMPLIFIER INPUT1 OFF FROM AMPLIFIER INPUT1 OFF POWER ON OFF POWER ON OFF Amplifier To AC outlet To AC outlet Notes on the above connections · When connected to line output terminals of the amplifier, other speakers should not be connected to the OUTPUT terminals on the rear panel of the subwoofer. If connected, they will not produce sound. · When connecting this unit to a monaural line output terminal of the amplifier, connect to either the left or right INPUT 2 terminal. * There may be a case that the power turns on unexpectedly by sensing noise from other appliances. If it occurs, set the AUTO STANDBY switch to the OFF or LOW position. * The level of low frequency input signal differs with each source, and each different part on the same source. So, this function may not operate properly depending on some sources. This function is available only when the power of this unit is on (by setting the STANDBY/ON button Y to ON). ¤ AUTO STANDBY switch With this switch, you can activate the Automatic Standby function. Normally, set the switch to the LOW position. To cancel this function, set the switch to the OFF position. * Change the setting of this switch only when the power of this unit is on standby (by setting the STANDBY/ON button to OFF). # PHASE switch Normally this switch is to be set to the REV (reverse) position. However, according to your speaker systems or the listening condition, there may be a case when better sound quality is obtained by setting this switch to the NOM (normal) position. Select the better position by monitoring the sound. < BASS switch YST-SW160 only By setting this switch to the MOVIE position, the bass sound in video software is well reproduced. By setting it to the MUSIC position, the bass sound in audio software is well reproduced. 7 ADJUSTING VOLUME Adjustment of the HIGH CUT control, the VOLUME control and the PHASE switch needs to be changed according to the main speakers, listening condition, source, etc. Front panel Rear panel PHASE YST-SW160 STANDBY/ON HIGH CUT VOLUME YST-SW90 STANDBY/ON HIGH CUT VOLUME NOM REV 40 Hz 140 Hz 0 10 50 Hz 150 Hz 0 10 3 1 2 3 4 5 5 1, 6 3 5 1, 6 7 Set the VOLUME control to minimum (0). Press the STANDBY/ON button to turn on this unit. Play any source and adjust the amplifier's volume control to the desired listening level. Adjust the HIGH CUT control according to the main speakers connected. Normally, set the control to the main speaker's rated minimum reproducible frequency*. [. . . ] AC 110/120/220/240 V, 50/60 Hz . . . . . . . . . . . . . . . . . . (Adjustable with Voltage Selector) Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 W Dimensions (W × H × D) . . . . . . . . . . . 235 mm × 602 mm × 463 mm (9-5/16" × 23-3/4" × 18-1/4") Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]