User manual YAMAHA YV-3910

[. . . ] CONCERT VIBES YV-3910/3710/3700/2700/2700G/1600A/520 Owner's Manual Make sure to read the PRECAUTIONS on page 1. SPECIAL MESSAGE SECTION This product utilizes an external power supply (adapter). DO NOT connect this product to any power supply or adapter other than one described in the manual, on the name plate, or specifically recommended by Yamaha. WARNING: Do not place this product in a position where anyone could walk on, trip over, or roll anything over power or connecting cords of any kind. The use of an extension cord is not recommended! [. . . ] Slide Leg Fixing Bolt Slide Leg Fixing Bolt Leg (Small) Slide Leg Slide Leg Fixing Bolt Slide Leg Fixing Bolt 1-1 q YV-3910/3710 : Place the large leg, small leg, pedal stay (and reinforcement stay : YV-3700) so that after assembly each part will be positioned as illustrated. Leg (Large) Low Sound Side Slant Shaft Audience Side Leg (Small) High Sound Side Pedal Stay Pedal Player Side Align flat surfaces. Flat surface should face player side. 6 ASSEMBLY: YV-3910/3710/3700 1-2 q YV-3910/3710 : Insert the pedal stay with its notch facing up into the lower joint of the large leg as far as it will go (aligning the notch with the fixing bolt) and tighten the fixing bolt securely. * The hole next to the notch serves as a reference for the correct insertion position. q YV-3910/3710 : Connect the other ends of the pedal stay with the small leg in the same way. 1-3 Leg (Large) Tighten Pedal Stay Fixing Bolt Reference Hole Leg (Large) Pedal Stay Notch Notch 1-4 q YV-3910/3710 : Loosen the slant shaft bolt, extend the shaft and insert the shaft end into the leg joint. With the notch aligned with the fixing bolt (the same as in the pedal stay assembly) tighten the fixing bolt securely. q YV-3910/3710 : Connect the other side slant shaft with the small leg in the same way. 1-5 Leg Joint Notch Slant Shaft Bolt 7 ASSEMBLY: YV-3910/3710/3700 1-1 q YV-3700 : Place the large leg, small leg, pedal stay (and reinforcement stay : YV3700) so that after assembly each part will be positioned as illustrated. Leg (Large) Reinforcement Stay Audience Side Low Sound Side Leg (Small) High Sound Side Pedal Stay Pedal Player Side Align flat surfaces. Flat surface should face player side. 1-2 q YV-3700 : Insert the pedal stay with its notch facing up into the lower joint of the large leg as far as it will go (aligning the notch with the fixing bolt) and tighten the fixing bolt securely. * The hole next to the notch serves as a reference for the correct insertion position. q YV-3700 : In the same way, insert the reinforcement stay with its notch facing down into the upper joint of the large leg and tighten the fixing bolt. q YV-3700 : Connect the other ends of both stays with the small leg in the same way. Leg (Large) Tighten Pedal Stay Notch 1-3 Fixing Bolt Reference Hole Leg (Large) Pedal Stay 1-4 Notch 8 ASSEMBLY: YV-3910/3710/3700 x Insert the rails (1) through (4) into the legs. 2-1 First, insert rail (2). * Do not insert the rail one side at a time, but at first alternately push in the left and right sides little by little , after which the rail can be pushed down until it stops. Next, securely insert the rails (3), (1) and (4), in this order. 2-2 Rail (1): With name plate. Rail (2): With rail clamp and more posts than rails (3) and (4). Rail (3): With rail clamp and less posts than rail (2). Resonator Holders Resonator Holders 12 ASSEMBLY: YV-3910/3710/3700 b Set the tone bars. 5-1 (Refer to the illustration of step 3-3 ) Raise the pedal until the knurled part is fully retracted, and fix the center rod by tightening the center rod fixing bolt. Engage the rail clamp on rail (2) and rail (3) with rail (1) and rail (4), respectively. 5-2 Rail (3) Rail (4) Rail Clamp Rail Clamp Rail (1) Rail (2) 5-3 Hold the pedal depressed to keep the sustain damper lowered, and then carefully set the tone bars. Align each tone bar individually, and hook its string onto the corresponding post. Confirm that all strings are secured to their posts, and then hook the two springs at the low sound side into each other. Low Sound Side High Sound Side Springs 13 ASSEMBLY: YV-3910/3710/3700 n Attach the driver. 6-1 Loosen the fixing bolts at the bottom of rails (2) and (3) on the high sound side, and slide both fittings in the direction of the low sound side. Fully insert the driver mount into the support fitting. Bottom View 6-2 6-1 6-2 Support Fitting Rail (2) Slide the fittings. Insert mount until it stops Rail (3) Driver Support Fitting Fittings Fixing Bolts Pulley Motor Unit 6-3 Slide the fittings moved in step 6-1 back in the direction of the high sound side. Engage the two side mounts on the driver securely with the fittings, and then tighten the fixing bolts to fasten the driver. * Set the driver so that the pulleys on either side are positioned directly below the fan side pulleys. Fitting Bottom View Fitting Tighten fixing bolts. Fixing Bolts Fitting 14 ASSEMBLY: YV-3910/3710/3700 m Attach the controller. 7-1 q YV-3910/3710 : Loosen the fixing bolt, slide out the controller hanger and hang the controller on the hanger. [. . . ] In the same way, insert the reinforcement stay with its notch facing down into the upper joint of the large leg and tighten the fixing bolt. Connect the other ends of both stays with the small leg in the same way. Leg (Large) Tighten Pedal Stay Notch 6 Fixing Bolt Pedal Stay 7 Notch Leg (Large) 22 ASSEMBLY : YV-2700/2700G/1600A/520 8 Connect the slide legs with the legs. Align the legs from above so that the slide legs slide into the corresponding leg holes. Adjust to the desired height and then securely tighten each slide leg fixing bolt, aligning it with the corresponding notch of the slide leg. [. . . ]