User manual ZALMAN 7700

[. . . ] Zalman is not responsible for any damage that occurs when moving a computer. 3. Exploded View Fan Grip (S-Type) Grip (L-Type) Clip Fan Fixing Screw Fan Support FHS Fan Support Fixing Screw 1 4. 00-54635 Korean Design Applications Nos. Patent Applications pending in over 20 nations around the world, including USA, EU, and Japan Precautions 1) If excessive force is exerted on the fan, it may malfunction and result in damage to the product and/or the computer. [. . . ] CPU Die 2) AMD Sempron / AMD64 - Socket 754/939/940 TD > TC All CPUs conforming to Socket 754/939/940 platform Cautions ) No components higher than 39mm (possible examples: PSU, graphics card, RAM etc. ) should be present within a 68mm radius from the center of the CPU. For more information, please visit the Zalman website (http://www. zalman. co. kr) and refer to CNPS7700 Compatible Socket 754/939/940 Motherboards List link. 3 7. Installation CNPS7700 must be used with a grip specific to each CPU socket. Refer to the table on the right to choose the correct grip for use. Socket 775 478 754/939/940 Grip S - Type L - Type L - Type Hole Hole Inner Hole Outer Hole 1) Intel Pentium 4 - Socket 775 Install Clip Support for Socket 775 Align the clip support for socket 775 and the backplate for socket 775 with the mounting holes on the motherboard and fasten them together using the clip support fixing bolts. The lever slot on the clip support should be properly oriented on the hinged side of the socket lever when installing. * The backplate support is used for the convenience of installation. You can remove it if it is not deemed necessary. Clip Support Fixing Bolt Clip Support for Socket 775 Motherboard Socket Lever Backplate for Socket 775 Backplate Support Lever Slot Socket Lever Hinge Lever Slot Apply Thermal Grease Clean off particles and residue from the top of the CPU then spread a generous amount of the included thermal grease thoroughly on top of the CPU. CPU (IHS) Unlike the flat-milled base of the FHS, the top surface of the LGA775 CPU may have minute dips and peaks causing pockets of non-contact between the FHS and CPU. Please apply a generous amount of thermal grease on the top of the CPU. Install Grips and Bolts Interlock the S-type grips with the clip. Insert the two bolts into the holes of the grips. Bolt Grip (S-Type) Place FHS Set the FHS at the center of the CPU. Screw the bolts in slightly, then tighten each bolt a few turns at a time while alternating between the two until the clip support is completely pressed against the grips. Grip (S-Type) Clip Support for Socket 775 Connect Power (How to use FAN MATE 2) Please refer to FAN MATE 2 Installation and Usage on page 7. 4 2) Intel Pentium 4 - 478 Apply Thermal Grease Clean off particles and residue from the top of the CPU then spread a thin layer of the included thermal grease thoroughly on top of the CPU. CPU (IHS) Install Clip Supports for Socket 478 Install the clip supports for socket 478 on both sides of the retention guide as shown in the diagram. Retention Guide Clip Support for Socket 478 Install Grips and Bolts Interlock the L-type grips with the clip. Insert the two bolts into the inner holes of the grips. Bolt Grip (L-Type) Inner Hole Place FHS Set the FHS at the center of the CPU. Screw the bolts in slightly, and then tighten each bolt a few turns at a time while alternating between the two until the clip supports are completely pressed against the grips. Grip (L-Type) Clip Support for Socket 478 Connect Power (How to use FAN MATE 2) Please refer to FAN MATE 2 Installation and Usage on page 7. 5 3) AMD Sempron/AMD64 - 754/939/940 Fasten Nipples Place a small washer on the motherboard. Then, put a nipple over it and fasten the nipple until the Backplate for AMD64 is firmly attached to the motherboard on the opposite side of the CPU. * A Retention Guide is not necessary for installing CNPS7700 on Socket 754/939/940. Nipple Motherboard Small Washer Backplate for AMD64 Apply Thermal Grease Clean off particles and residue from the top of the CPU then spread a thin layer of the included thermal grease thoroughly on top of the CPU. CPU (Lid) Install Grips and Bolts Interlock the L-Type grips with the clip. Insert the two bolts into the outer holes of the grips. Bolt Grip (L-Type) Place FHS Outer Hole Set the FHS at the center of the CPU. Screw the bolts in slightly, and then tighten each bolt a few turns at a time while alternating between the two until the nipples are completely pressed against the grips. Grip (L-Type) Nipple Connect Power (How to use FAN MATE 2) Please refer to FAN MATE 2 Installation and Usage on page 7. 6 FAN MATE 2 Installation and Usage 1) Installing FAN MATE 2 on the Inside of the System Fan Connector (CNPS7700) 2) Installing FAN MATE 2 on the Outside of the System Double-sided Tape FAN MATE 2 Motherboard 6-Pin Connector Connect the appropriate 3-pin connector on the cable to the motherboard fan header and the CNPS7700's fan connector. Pull the 6-pin connector out of the system through the back and connect it to FAN MATE 2, which should be installed on the case using the included double-sided tape. When the speed control knob on FAN MATE 2 is turned fully counter-clockwise, the fan operates in Silent Mode. Turned fully clockwise, it operates in Normal Mode. [. . . ] is not responsible for any damage resulting from CPU OVERCLOCKING. ) 7 9. Zalman Noise Prevention System When building a noiseless computer, use Zalman's Noiseless Power Supply, Noiseless Case Fan, Fanless Northbridge Cooler, Heatpipe HDD Cooler, Heatpipe VGA Cooler, and Fan Controller to achieve stable performance and maintain a noiseless environment. 10. TNN (Totally No Noise) Computer Case The TNN 500AF is the world's first absolutely noiseless, anti-dust computer casefor high-end systems that has been developed with Heatpipe Technology, HSC (Heat Source Contact) Power Technology, High Capacity Extrusion Technique, and FMS (Flexible Mounting Structure) Design Technology by ZALMAN Tech Co. , Ltd. The TNN 500AF package includes a high performance aluminum computer case with an absolutely noiseless cooling solution that does not require the use of a fan, making it ideal for: 1. [. . . ]