User manual ZALMAN 7700LED

[. . . ] Zalman is not responsible for any damage that occurs when moving a computer. (Note 2) The cooler fan operates at 2, 300rpm if connected directly to the motherboard's power connector without the use of FAN MATE 2. (Note 3) Noise measured 1m distance away from source. 3. [. . . ] Please do not install the CNPS7700 LED if this interference is observed. 10. 2mm Motherboard component height restriction Grip Motherboard Component 4mm Motherboard Component Figure 1 Compatible Grip Figure 2 Not Compatible For more information, please visit Zalman's website (http://www. zalman. co. kr) and click on the links of "Compatibility between CNPS7700 and Socket 478 Pentium 4 Motherboards". 3) AMD Sempron / AMD64 - Socket 754/939/940 All CPUs conforming to Socket 754/939/940 platform Caution) No components higher than 39mm (possible examples : PSU, graphics card, RAM etc. ) should be present within a 68mm radius from the center of the CPU. For more information, please visit Zalman's website (http://www. zalman. co. kr) and refer to "CNPS7700 Compatible Socket 754/939/940 Motherboards List" link. 3 7. Installation CNPS7700 LED must be used with a specific grip for each CPU socket. Refer to the table on the right to choose the correct grip. Socket 775 478 754/939/940 Grip S - Type L - Type L - Type Hole Hole Inner Hole Outer Hole 1) Intel Dual Core Pentium/Intel Pentium 4 - Socket 775 Installation of Clip Support for Socket 775 Align the clip support for socket 775 and the backplate for socket 775 with the mounting holes on the motherboard and fasten them together using the clip support fixing bolts. The lever slot on the clip support should be properly oriented on the hinged side of the socket lever when installing. The backplate support is used for the convenience of installation. You can remove it if it is not deemed necessary. Clip Support Fixing Bolt Clip Support for Socket 775 Motherboard Socket Lever Backplate for Socket 775 Backplate Support Lever Slot Socket Lever Hinge Lever Slot Thermal Grease Application Clear off particles and residue from the top of the CPU then spread a generous amount of the included thermal grease thoroughly on top of the CPU. CPU (IHS) Thermal Grease Unlike the flat-milled base of the FHS, the top surface of the LGA775 CPU may have minute dips and peaks causing pockets of non-contact between the FHS and CPU. Please apply a generous amount of thermal grease on the top of the CPU. Installation of Grips and Bolts Interlock the S-type grips with the clip. Insert the two bolts into the holes of the grips. Bolt Grip (S-Type) FHS Placement Set the FHS at the center of the CPU. Screw the bolts in slightly, then tighten each bolt a few turns at a time while alternating between the two until the Grips are completely pressed against the Clip Support. Grip (S-Type) Clip Support for Socket 775 Connect Power (Use FAN MATE 2) Please refer to FAN MATE 2 Installation and Usage on page 7. 4 2) Intel Pentium 4 - Socket 478 Thermal Grease Application CPU (IHS) Clear off particles and residue from the top of the CPU then spread a thin layer of the included thermal grease thoroughly on top of the CPU. Thermal Grease Installation of Clip Supports for Socket 478 Install the clip supports for socket 478 on both sides of the retention guide as shown in the diagram. Retention Guide Clip Support for Socket 478 Installation of Grips and Bolts Interlock the L-type grips with the clip. Insert the two bolts into the inner holes of the grips. Bolt Grip (L-Type) Inner Hole FHS Placement Set the FHS at the center of the CPU. Screw the bolts in slightly, and then tighten each bolt a few turns at a time while alternating between the two until the Grips are completely pressed against the Clip Support. Grip (L-Type) Clip Support for Socket 478 Connect Power (Use FAN MATE 2) Please refer to FAN MATE 2 Installation and Usage on page 7. 5 3) AMD Sempron/AMD64 - Socket 754/939/940 Nipple Installation Place a small washer on the motherboard. Then, put a nipple over it and fasten the nipple until the Backplate for AMD64 is firmly attached to the motherboard on the opposite side of the CPU. * A Retention Guide is not necessary for installing CNPS7700 LED on Socket 754/939/940. Nipple Small Washer Motherboard Backplate for AMD64 Thermal Grease Application Clear off particles and residue from the top of the CPU then spread a thin layer of the included thermal grease thoroughly on top of the CPU. Installation of Grips and Bolts Interlock the L-Type grips with the clip. Insert the two bolts into the outer holes of the grips. [. . . ] For more information on updating your BIOS, please refer to your motherboard manufacturer's website. Disabling CPU fan speed detection in BIOS settings does not affect computer performance. 3) Overclocking The fan should be set to Normal Mode if Overclocking. is not responsible for any damage resulting from CPU Overclocking. ) 7 9. [. . . ]