User manual ZALMAN 8000

[. . . ] 3) Optimized fin design for lightness and higher performance. 5) Compatible with Slim and Low Profile Computer Enclosures. 6) Compatible with Intel Pentium D (Socket 775), Intel Pentium 4 (Socket 775), AMD Athlon 64 X2 (Socket 939), and AMD Sempron/AMD64 (Socket 754/939/940). 7) FAN MATE 2 included for manual adjustment of fan speed. 2. [. . . ] Familiarize yourself with the "Installation" steps before installing the CNPS8000. 6) See the picture on the right for product dimensions to check whether the product interferes with any motherboard components. 6) Avoid inserting objects or fingers into the fan while it is in operation. 54mm 50mm 58mm VGA Card Slot Case chassis Cover 62. 5mm ODD 54mm 6. Components 1) Common Components One CNPS8000 One Thermal Grease One FAN MATE 2 (Fan Speed Controller) One Cable for FAN MATE 2 One Double-sided Tape (for attaching FAN MATE 2) One User's Manual 2) Components for Intel Pentium D/Pentium 4 (Socket 775) Two Clips for Socket 775 One Backplate for Socket 775 3) Components for AMD AMD64 (Socket 754/939/940) One Clip-A for AMD64 One Clip-B for AMD64 System Fan 2 7. Compatible CPUs 1) All Intel Socket 775 CPUs - Pentium D - Pentium 4 - Celeron D 2) All AMD Socket 754/939/940 CPUs - Opteron - Athlon 64 X2 - Athlon 64 FX - Athlon 64 - Sempron Air Guide equipped cases recommended for CPUs with high TDP. Zalman's Super Thermal Grease recommended for better thermal performance. 8. Installation 1) Intel Pentium D / Pentium 4 - Socket 775 Backplate Installation Remove the protective film of theBackplate for Socket 775, and attach the backplate after aligning it with the holes from the backside of motherboard. Mounting hole Nipple Protective Film Backplate for Socket 775 Thermal Grease Application Clear off any particles and residue from the top of the CPU then spread the enclosed Thermal Grease generously on the surface of the CPU that makes contact with the base of CNPS8000. Thermal Grease CPU(IHS) Clip Installation Inter rock the pair of Clips for socket 775 by sliding them into each other between the heatsink's base and fin. Caution) The arrowhead marking on each clip must be in line with the arrowhead markings on the heatsink's base. Base Bolt Clip for Socket 775 Cooler Installation Place the CNPS8000 on the center of the CPU. Slightly screw the four bolts onto the backplate's nipples, then tighten each bolt one rotation at a time until all are completely tightened. Note 1) Excessive force can result in damage to the nipples. Note 2) Exerting excessive force on the fan with the driver can result in malfunction. Power Connection (FAN MATE2 Installation) Please refer to FAN MATE 2 Installation and Usage on page 5. 3 2) AMD Sempron / AMD64 - Socket 754/939/940 Thermal Grease Application Clear off any particles and residue from the top of the CPU then spread the enclosed Thermal Grease thinly on the surface of the CPU that makes contact with the base of CNPS8000. Thermal Grease CPU(Lid) Clip Installation Inter rock the pair of Clips for AMD 64 by sliding them into each other between the heatsink's base and fin. Caution) The arrowhead marking on each clip must be in line with the arrowhead markings on the heatsink's base. Clip-A for AMD64 Base Clip-B for AMD64 Cooler Installation Hook the hole of Clip-B onto the retention frame's lug. Then hook the hole of Clip-A onto the retention frame's lug by pressing down on the lever of the Clip-A. Note ) Set the direction of the Clips in a manner so that there is no interference with other components of the motherboard. Lever Clip slot Lug Uninstalling the Cooler To uninstall the CNPS8000, press onto the clip slot with the use of a ( lever to disconnect the clip hole from the retention frame's lug. ) driver, then push off the Power Connection (FAN MATE2 Installation) Please refer to FAN MATE 2 Installation and Usage on page 5. 4 9. FAN MATE 2 Installation and Usage 1) Installing FAN MATE 2 on the Inside of the System 2) Installing FAN MATE 2 on the Outside of the System Double - sided Tape Fan Connector (CNPS8000) FAN MATE 2 6-Pin Connector Motherboard Connect the appropriate 3-pin connector on the cable to the motherboard fan header and the CNPS8000's fan connector. Pull the 6-pin connector out of the system through the back and connect it to FAN MATE 2, which should be installed on the case using the included double-sided tape ( ). When the speed control knob on FAN MATE 2 is turned fully counter-clockwise, the fan operates in Silent Mode. [. . . ] is not responsible for any damages in CPU resulting from OVERCLOCKING. 5 11. Zalman Computer Noise Prevention System The use of Zalman's Noiseless Power Supply, CPU Cooler, Case Fan, Fanless Northbridge Cooler, and Video Card Cooler will allow you to achieve stable performance and maintain a noiseless environment. 12. TNN (Totally No Noise) Computer Enclosures TNN 300 TNN 500AF TNN Computer Enclosures are the world's first environment-friendly noiseless computer enclosures that operate without the use of a fan. TNN Computer Enclosures use the aluminum enclosure itself as a heatsink. [. . . ]