User manual ZALMAN 9500

[. . . ] Special care should be taken when moving a computer equipped with a cooler that exceeds the specified weight limit. Zalman is not responsible for any damage that occurs when moving a computer. 3. Exploded View Fan Support Fixing Bolt Heat sink Fan Fan Support CPU Block Cover CPU Block Fixing Bolt 1 4. 05-15303, 15304, 15306, 15307, 17970, 17971 Patent Applications pending in over 20 nations around the world including USA, EU, and Japan 5. [. . . ] Then spread the included thermal grease ( ) thinly on top of the CPU. Thermal Grease CPU (IHS) Place Cooler Insert two bolts ( ) into holes on the clip (S-Type, ) and place CNPS9500 at the center of the CPU. Then, fasten the bolts in an alternating manner until the clip ( ) is completely pressed against the clip supports. Bolt, Clip(S-Type), Caution When installing CNPS9500 on a motherboard with horizontally-oriented retention guide, take extra care not to let the screwdriver exert excessive force on the fan. If excessive force is exerted on the fan, it may cause a malfunction. Connect Power (Use FAN MATE 2) Please refer to FAN MATE 2 installation and usage on page 7. 4 2) Intel Pentium 4 - Socket 478 Install Clip Refer to "How to Install the CNPS9500's Clip" on page 3 to correctly install the clip (S - Type, CNPS9500. Apply Thermal Grease Clean off particles and residue from the top of the CPU. Then spread the included thermal grease ( ) thinly on top of the CPU. Thermal Grease ) on CPU (IHS) Install Clip Support for Socket 478 Install the two clip supports for Socket 478 ( ) on both sides of the retention guide as shown in the diagram. Clip Support for Socket 478, Place Cooler Insert two installation bolts for Socket 478 ( ) into holes on the clip (S-Type, ) and place CNPS9500 at the center of the CPU. Using the L-wrench ( ), fasten the bolts for Socket 478( ) into each hole on the clip support for Socket 478( ) slightly at first. Then, fasten the bolts ( ) in an alternating manner until the clip ( ) is completely pressed against the clip supports. Installation Bolt for Socket 478, Clip(S-Type), When installing CNPS9500 on a motherboard with horizontally-oriented retention guide, take extra care not to let the L-wrench ( ) exert excessive force on the fan. If excessive force is exerted on the fan, it may cause a malfunction. L-wrench, Connect Power (Use FAN MATE 2) Please refer to FAN MATE 2 installation and usage on page 7. 5 3) AMD Sempron/AMD64 - Socket 754/939/940 When CNPS9500 is installed on an AMD system, the existing cooler installation framework (retention frame, backplate, screws) is used for the installation. Install Clip Refer to "How to Install the CNPS9500's Clip" on page 3 to correctly install the clip (L-Type, CNPS9500. Separate Retention Frame Fixing Screws Unscrew the screws that fix the existing retention frame onto its place. Apply Thermal Grease Clean off particles and residue from the top of the CPU. Then spread the included thermal grease ( ) thinly on top of the CPU. ) on Thermal Grease CPU (Lid) Place Cooler Place CNPS9500 at the center of the CPU. Fasten the retention frame fixing screws onto the backplate through the outer holes of the clip (L-type, ) slightly at first. Then, fasten the screws in an alternating manner until the clip ( ) Screw is completely pressed against the retention frame. Clip(L-Type), When installing CNPS9500 on a motherboard with horizontally-oriented retention guide, take extra care not to let the screwdriver exert excessive force on the fan. If excessive force is exerted on the fan, it may cause a malfunction. Motherboards with Pushpin - type Retention Frame need the included nipples ( ) and bolts ( ) for installation of the cooler. Remove the push-pins from the retention frame, and insert the nipples ( ) into it. Fasten them to the backplate using the bolts ( ) and follow these steps in order : Apply Thermal Grease Place Cooler Nipple, Bolt, Retention Frame Connect Power (Use FAN MATE 2) Bolt, Please refer to FAN MATE 2 installation and usage on page 7. 6 10. FAN MATE 2 Installation and Usage 1) Installing FAN MATE 2 on the Inside of the System 2) Installing FAN MATE 2 on the Outside of the System Double - sided Tape Fan Connector (CNPS9500) FAN MATE 2 6-Pin Connector Motherboard Connect the appropriate 3-pin connector on the cable to the motherboard fan header and the CNPS9500's fan connector. Pull the 6-pin connector out of the system through the back and connect it to FAN MATE 2, which should be installed on the case using the included double-sided tape ( ). When the speed control knob on FAN MATE 2 is turned fully counter-clockwise, the fan operates in Silent Mode. Turned fully clockwise, it operates in Normal Mode. You can select the desired fan speed by turning the knob. [. . . ] is not responsible for any damage resulting from CPU OVERCLOCKING. 7 12. Zalman Noise Prevention System When building a noiseless computer, use Zalman's Noiseless Power Supply, CPU Cooler, Case Fan, Fanless Northbridge Cooler, and Video Card Cooler to achieve stable performance and maintain a noiseless environment. 13. TNN (Totally No Noise) Computer Case The TNN 500AF is the world's first absolutely noiseless, anti-dust computer case for high-end systems that has been developed with Heatpipe Technology, HSC (Heat Source Contact) Power Technology, High Capacity Extrusion Technique, and FMS (Flexible Mounting Structure) Design Technology by ZALMAN Tech Co. , Ltd. The TNN 500AF package includes a high performance aluminum computer case with an absolutely noiseless cooling solution that does not require the use of a fan, making it ideal for : 1. [. . . ]