User manual ZALMAN CNPS5100(S)

[. . . ] 4) With the included adjustable fan speed connector, the user can freely adjust the CPU fan's RPM. 5) Zalman's CPU Coolers cool a CPU to a temperature sufficiently below the temperature required by the CPU manufacturer without generating noise. 6) Zalman's CPU Coolers offer very stable operation of a CPU in an OVERCLOCKED environment. [. . . ] However, this will not affect the performance. Korean Patent Application No. 01-11056 Patent Applications Pending in over 20 nations around the world, including the U. S. , EU, and Japan * The specifications of any product may change without prior notice to improve the performance thereof. 1. First, check whether your CPU is a P4 CPU or an AMD CPU. Then, depending on the type of CPU, insert the bolts (A or B) into the appropriate holes in the cooler body (See Figure 1). Intel P4 CPU AMD CPU < Figure 1 > 2. Check whether or not nipples (spacers) for installing a CPU cooler are mounted between the mainboard and the computer case. Installation in a Computer Case Having Nipples (spacers) for Installing a CPU Cooler (See Figure 2) Spring Bolt A(59 63mm) Mainboard Case Nipple Case Hole Mainboard < Figure 2 > (1) Insert one of the provided bolts A into a tapered spring as shown in Figure 2, and insert the bolt A into an appropriate mounting hole (See Figure 1) of the cooler body. Repeat until four bolts are in stalled in the cooler body. The diameter of the spring increases from one end to the other end. The end of the spring having a smaller diameter should be directed to the head of the bolt as shown in Figure 3. ) (2) Spread the thermal grease, which is provided together with the cooler, on the surface of the CPU core. Case Good Bad < Figure 3 > * The specifications of any product may change without prior notice to improve the performance thereof. (3) Check the locations of the holes around the socket and those of the bolts A mounted in the mounting holes, and then place the FHS horizontally on the center of the CPU. (4) To make the FHS completely contact the CPU core (this is important to protect the CPU core from overheating), tighten each bolt A by one turn in the order shown in Figure 2 (i. e. , in a diagonal sequence) with a screw driver until they no longer go in (as shown in Figure 4). Mainboard Case Good < Figure 4 > Bad Installation in a Computer Case That Does Not Have Nipples for Installing a CPU Cooler (See Figure 5) Spring Bolt B(42 47mm) Mainboard Case Mainboard Case Nipple Washer (A or B) Hole Washer B Bolt C(6 13mm) < Figure 5 > (1) Detach the mainboard from the computer case. Mount the provided nipples, bolts C, and washers (A or B) on the mainboard as shown in Figures 5 and 6, then reattach the mainboard to the computer case. Different washers are used depending on the size of the holes formed around the CPU socket on the mainboard. That is, if the size of the holes is 6 mm as shown in Figure 6(A), washer A and B is used, and if the size of the holes is 4 mm as shown in Figure 6(B), only washer B is used. A bolt with a washer is used for the upper part of the mainboard and another bolt with a washer isused for the lower part of the mainboard. ) Washer A (Inside Diameter : 6mm) Nipple Washer B (Inside Diameter : 4mm) Mainboard <A> Washer B (Inside Diameter : 4mm) < Figure 6 > Bolt C <B> * The specifications of any product may change without prior notice to improve the performance thereof. (2) Insert one of the provided bolts B into a tapered spring as shown in Figure 5, and insert the bolt B into an appropriate mounting hole of the cooler body (See Figure 1). Repeat until four bolts are installed in the cooler body. The diameter of the spring increases from one end to the other end. The end of the spring having a smaller diameter should be directed to the head of the bolt as shown in Figure 7. ) Good Bad < Figure 7 > (3) Spread the thermal grease, which is provided together with the cooler, on the surface of the CPU core. (4) Check the locations of the nipple holes on the mainboard and the locations of the bolts B, and then place the Cooler horizontally on the center of the CPU. To make the FHS completely contact the CPU core (this is important to protect the CPU core from overheating), tighten each bolt B by one turn in the order shown in Figure 5 (i. e. , in a Good Bad Bad diagonal sequence) with a screw driver. [. . . ] When the speed control knob is turned fully counter-clockwise, the fan speed is minimum and the fan operates in silent mode. You can select the desired fan speed by turning the knob. Note 2) FAN MATE 1 has been specifically designed for the fan of this product. [. . . ]