User manual ZALMAN FS-V7

[. . . ] The next year I won the same title playing Unreal Tournament 2003, becoming the only three-time CPL champion. And I did it playing a different game each year, something no one else has ever done and a feat of which I am extremely proud. At QuakeCon 2002, I faced off against my rival ZeRo4 in one of the most highly anticipated matches of the year, winning in a 14 to (-1) killer victory. Competing at Quakecon 2004, I became the World's 1st Doom3 Champion by defeating Daler in a series of very challenging matches and earning $25, 000 for the victory. LIVIN' LARGE Since my first big tournament wins, I have been a "Professional Cyberathlete", traveling the world and livin' large with lots of international media coverage on outlets such as MTV, ESPN and G4TV to name only a few. [. . . ] Important Notices 1. 1) Please read this manual thoroughly before installation. 1. 2) After installing this product on a VGA(Video Graphics Array) card, a PCI slot adjacent to the AGP (or PCIe) slot will become unusable. 1. 3) Before installing on a newly released VGA card, please check for compatibility at Fatal1ty's website* or Zalman's website**. 1. 4) This product is not compatible with Matrox VGA cards and NVIDIA PCX 5*** VGA cards. 1. 5) If the VGA card and its components interfere with the installation of this product, stop the installation, refer to the list of compatible VGA cards at Fatal1ty's website* or Zalman's website**, and install this product with one of the compatible VGA cards. 1. 6) A rear case fan is recommended for enhancing the performance of this product. * www. fatal1ty. com ** www. zalman. co. kr Disclaimer Zalman Tech Co. , Ltd. , Fatal1ty, Inc. , and any of its partners are not responsible for any damages due to external causes, including but not limited to, improper use, problems with electrical power, accident, neglect, alteration, repair, improper installation, or improper testing. 2. Features 2. 1) Pure copper heatsink with ultra large surface area for maximum cooling performance. 2. 2) 80mm fan (with red LEDs) installed in the heatsink (FHS) cools not only the VGA chipset and VGA RAM, but all other VGA components as well. 2. 3) Quiet Mode(5V) and Performance Mode(12V) selection provided to accommodate the user's environment and preference. 3. Specifications 3. 1) FHS Assembly (Flower Heatsink & Fan) 3. 1. 1) Dimensions : 91(L) x 126. 4(W) x 30(H)mm 3. 1. 2) Weight : 270g 3. 1. 3) Base Material : Pure Copper 3. 2) Fan Specifications 3. 2. 1) Dimensions: 3. 2. 2) Bearing Type : 3. 2. 3) Fan Speed : 3. 2. 4) Noise Level : 80(L) x 80(W) x 15(H)mm 2 Ball-Bearing Sets 2, 050 rpm ±10% (Quiet Mode), 3, 500 rpm ±10% (Performance Mode) 23. 7 dB ±10% (Quiet Mode), 36dB ±10% (Performance Mode) 4. Components FHS Assembly(Flower Heatsink & Fan) Eight (8) RAM Heatsinks One (1) Brace Plate Two (2) Nipple `A' Two (2) Nipple `B' Four (4) Bolt 'A' (Ø3 x 5mm) Four (4) Bolt 'B' (Ø4 x 4mm) Six (6) Rubber Rings Thermal Grease One (1) Multi-Connector User's Manual User's Manual 5. Exploded View 2) Bolt `A' 3) FHS Assembly 4) RAM Heatsink 1) VGA RAM 5) Nipple `A' 6) Rubber Ring 7) VGA Chipset 8) Rubber Ring 9) Nipple `B' 10) RAM Heatsink 11) Brace Plate 12) Bolt 'B' 6. Installation Procedure The following installation sequence MUST be followed. (Nipple `A' and `B' Brace Plate VGA RAM Heatsinks Thermal Grease Application VGA Cooler VGA Card Supply Power) 1) Nipple `A' 2) Rubber Ring 3) Mounting Hole 4) Rubber Ring A B Nipples 5) Nipple `B' 6. 1) Install Nipples `A' and `B' Check the VGA card for compatible installation hole positions. Install Nipple `A' and Nipple `B' on the heatsink Mounting Holes as shown in the diagram. Remember to use Rubber Rings in between. Warning) The Nipples MUST be tightened by hand. [. . . ] Apply Thermal Grease on the VGA Chipset's core that makes contact with the base of the FHS Assembly. 1) Thermal Grease 2) RAM Heatsink 3) Nipple `A' 4) VGA Chipset 6. 5) Install the FHS Assembly Align the FHS Assembly's base on the center of the VGA Chipset. Screw each Bolt `A' on each Nipple `A' slightly, and tighten each Bolt `A' a few turns at a time, alternating between each bolt, until the Clip is completely attached to each Nipple `A'. Note) Make sure that the heatsink's base and the VGA Chipset are completely in contact with each other. 1) Bolt `A' 2) FHS Assembly 3) Clip 4) Nipple `A' 5) VGA Chipset 6. 6) Install the VGA Card Insert the assembled VGA card into the motherboard's AGP (or PCIe) slot. [. . . ]