User manual ZANKER AE2050

[. . . ] Switching the double ring cooking zone on and off . Switching the power function on and off . 4 4 5 5 5 6 6 6 7 7 7 7 8 9 9 10 11 13 14 14 14 15 15 16 17 19 20 21 22 25 26 27 Installation Instructions . . 3 Operating Instructions 1 Safety instructions 3 Please comply with these instructions. [. . . ] Thereafter the actual heat setting is displayed. The time counts down. Displaying the time remaining for a cooking zone Step 1. Control panel field Select cooking zone Display Pilot light of the cooking zone selected flashes faster The time remaining is displayed After a few seconds the pilot light flashes more slowly. Switching off the acoustic signal Step 1. Control panel field Touch Acoustic signal Acoustic signal to acknowledge. Acoustic signal stops. 12 Safety cut-out Cooking surface If after switching on the cooking surface, a heat setting is not set for a cooking zone within approx. 10 seconds, the cooking surface automatically switches itself off. If one or more sensor fields are covered for longer than approx. by a pan placed upon it, a signal sounds and the cooking surface switches off automatically. If all cooking zones are switched off, the cooking surface automatically switches itself off after approx. 10 seconds. Control panel 3 Moisture (e. g. a wet cloth) or liquid boiling over onto the control panel immediately switches all cooking zones off. Induction cooking zones In the event of overheating (e. g. when a pan boils dry) the cooking zone automatically switches itself off. Remove residues by sliding the blade over the surface. Wipe the appliance with a damp cloth and a little washing up liquid. Rub the appliance dry using a clean cloth. Remove Type of dirt sugar, food containing sugar plastics, tin foil limescale and water rings fat splashes shiny metallic discolorations immediately yes yes ------when the appliance has cooled down ----yes yes yes cleaner for glass ceramic or stainless steel* using a scraper* *Scrapers and cleaners for glass ceramic and stainless steel can be purchased in specialist shops 3 Remove stubborn residuessteel. a cleaner for with glass ceramic or stainless 3 Scratches orbedark stainsdo not however affect on the glass ceramic that cannot removed the functioning of the appliance. 16 What to do if . . . Problem The cooking zones will not switch on or are not functioning Possible cause Remedy More than 10 seconds have passed Switch the appliance on again. since the appliance was switched on The lock is switched on l Switch off the lock (See the section "Locking/unlocking the control panel") The child safety device is switched Deactivate the child safety device on l (See the section "Child safety device") Several sensor fields were touched Only touch one sensor field at the same time The sensor fields are partly covered Remove the cloth or the liquid. by a damp cloth or with liquid Switch the appliance on again. Safety cut-out has been triggered The residual heat indicator is not displaying anything Switch the appliance on again The cooking zone was only on for a If the cooking zone is supposed to short time and is therefore not hot be hot, call the Customer Service Department. Let the cooking zone cool down The highest heat setting has the same power as the automatic warm up function Uncover sensor field The automatic warm up function is There is still residual heat on the not switching itself on cooking zone h The highest heat setting is set Repeated acoustic signal (6x), appliance switches off One or more sensor fields have been covered for longer than 10 seconds Acoustic signal sounds and appli- The On/Off sensor field has been ance switches itself on and then off covered up, e. g. by a cloth again; after 5 seconds another acoustic signal sounds Display is switching between two heat settings Do not place any objects on the control panel Power management is reducing the See the section "Switching the power of this cooking zone power function on and off" Unsuitable cookware No cookware on the cooking zone Use suitable cookware Place cookware on the cooking zone f flashes The diameter of the bottom of the Move onto a smaller cooking zone cookware is too small for the cook- Use suitable cookware ing zone _ is lit e and number are displayed Overheating protection for the cooking zone has been triggered Electronics fault Switch off the cooking zone. Switch the cooking zone on again Disconnect the appliance from the electrical supply for a few minutes (Take the fuse out of the house's wiring system) If after switching on again, e is displayed again, call the customer service department 17 If you are unable to remedy the problem by following the above suggestions, please contact your dealer or the Customer Care Department. 1 Warning! [. . . ] The latter is available from the Customer Care Department. A device must be provided in the electrical installation which allows the appliance to be disconnected from the mains at all poles with a contact opening width of at least 3 mm 1 IMPORTANT! 20 Electrical Connection Diagram For UK only: 230V. . . 240V~ 21 Assembly 22 23 24 Warranty conditions Standard guarantee conditions We, Zanussi, undertake that if within 24 months of the date of the purchase this Zanussi appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: The appliance has been correctly installed and used only on the electricity supply stated on the rating plate. The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer's instructions. The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by us. [. . . ]