User manual ZANKER CP5W

[. . . ] It is dangerous to alter the specifications or attempt to modify this product in any way. Care must be taken to ensure that the appliance does not stand on the electrical supply cable. Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person. s s Care should be taken when cleaning the bottom door seal and hinge area as any exposed metal edges may cut if care is not taken. [. . . ] Arrange the spoons, dessert spoons, knives and other small items of cutlery in the racks on both sides of the cutlery basket. UI03 34 PBA09GB The upper basket The upper basket is designed for plates (dessert plates, saucers, dinner plates of up to 24 cm in diameter), salad bowls, cups and glasses; Glasses with long stems can be placed upside down in the raised cup racks. Larger plates (dinner plates up to 24 cm in diameter) must be loaded in the front part of the upper basket. Light items (plastic bowls etc. ) should be loaded in the upper basket and arranged so they do not move. Before closing the door, ensure that the spray arms can rotate freely. US17 IEC 436 / DIN 44990 Adjusting the height of the upper basket If washing very large plates (over 27 cm and up to 31 cm in diameter) you can load them in the lower basket after moving the upper basket to the higher position. Certain types of glass can also become opaque after being washed several times in a dishwasher. A chemical reaction can occur between silver cutlery and stainless steel cutlery. Iron and cast iron objects can rust and stain other items. Aluminium tends to go black, copper, pewter and brass tend to stain. If in doubt check with manufacturer of the item. When buying new dishes, ensure that they are dishwasher proof. 36 PHT02GB Washing programmes Programme Degree of soil and type of load Heavy soil. Crockery, cutlery pots and pans Normal soil. We recommend every 3 months to run a 65°C wash programme without dishes using detergent. Cleaning the central filter (After each wash) Scraps of food may accumulate in the drain filter (A) and should be removed by rinsing the filter under running water. To remove the drain filter: simply pull it out by the handle. Once cleaned, refit the filter by pushing it back to its original position until it engages. A MA04 Cleaning the large filter (Every two months) If necessary clean the large filter (B) on both sides under running water, using a brush. To remove the large filter: Remove the spray arm by pulling it upward on one side. Turn the column (C) anticlockwise by 90° and then slide out the filter. Once cleaned refit it following the above instructions in reverse order. Ensure the filter is in its original position, the handle of the drain filter should be pointing towards the front of the appliance. The dishwasher must not be used without filters. Incorrect repositioning and fitting of the filters will produce poor washing results. Cleaning the filters is vital to ensure correct operation of the machine. 90° B C MA05 39 PMC01GB External cleaning Clean the external surfaces of the machine and control panel with a damp soft cloth. If necessary use only neutral detergents. Never use abrasive products, scouring pads or solvent (acetone, trichloroethylene etc. . . . ). Prolonged periods of non-operation If you are not using the machine for any period of time you are advised to: Unplug the appliance and then turn off the water; Fill the rinse aid dispenser; Leave the door ajar to prevent the formation of any unpleasant smells; Leave the inside of the machine clean. Frost precautions Avoid placing the machine in a location where the temperature is below 0°C. If this is unavoidable, empty the machine, close the appliance door, disconnect the water inlet pipe and empty it. Moving the machine If you have to move the machine (moving house etc. . . . ): Unplug it; Turn the water tap off; Remove the water inlet and discharge; Pull the machine out together with the hoses. Avoid over tilting the machine during transport. 40 PMC02GB Something not working Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer. Before contacting your local Service Force Centre, please carry out the checks listed below. Symptom The machine will not start Solution s s s s The door has not been properly closed. [. . . ] The rear foot is adjusted by turning the screw in the middle of the front kick plate to the left or right. Pads are supplied for the feet to make sliding the appliance in and out of the recess easier. To fit the pads, press them onto the feet. If required, the dimensions of these pads can be reduced by breaking them where marked. [. . . ]