User manual ZANKER LUXUS763

[. . . ] · The hood should not be used by children or persons not instructed in its correct use. MAINTENANCE · Switch off or unplug the appliance from the mains supply before carrying out any maintenance work. · Clean and/or replace the Filters after the specified time period. · Clean the hood using a damp cloth and a neutral liquid detergent. 11 GB CHARACTERISTICS Dimensions ø 120 280 L 0÷152 Hood Type L 45 448 50 498 55 548 60 598 70 698 80 798 175 175 90 898 Components 12e 8 12a 8 20 Ref. [. . . ] · Clean the hood using a damp cloth and a neutral liquid detergent. 11 GB CHARACTERISTICS Dimensions ø 120 280 L 0÷152 Hood Type L 45 448 50 498 55 548 60 598 70 698 80 798 175 175 90 898 Components 12e 8 12a 8 20 Ref. 1 Q. ty Product Components 1 Hood Body, complete with: Controls, Light, Blower, Filters 1 Directional Air Outlet grille 1 Closing element Q. ty Installation Components 4 Screws 4, 2 x 44, 4 2 Screws 2, 9 x 9, 5 Q. ty Documentation 1 Instruction Manual 1 20 GB 12 INSTALLATION Drilling the Support surface and Fitting the Hood SCREW FITTING · The hood support surface must be 135 mm above the bottom surface of the wall units. · Drill the support with a ø 4. 5 mm drill bit, using the drilling template provided. · Cut a hole ø 125 mm in size on the support surface, using the drilling template provided. · Fix using the 4 screws 12a (4, 2 x 44, 4) provided. 125 135 SNAP-ON FITTING · The hood can be installed either directly on the bottom surface of the wall units (min. 650 mm above the hob) using snap-on side supports. · Cut a fitted opening in the bottom surface of the wall unit, as shown. · Insert the hood until the side supports snap into place. · Lock in position by tightening the screws Vf from underneath the hood. Hood Type L1 45 352 50 402 55 452 60 502 70 602 80 702 90 802 12a 264 15 L1 Vf 13 GB CLOSING ELEMENT · The space between the edge of the hood and the rear wall can be closed by applying the element 20 provided, using the screws supplied for this purpose. 20 Connections RECIRCULATION VERSION AIR OUTLET · Cut a hole ø 125 mm in the wall unit over the hood. · Remove the fIlter retaining clips. · Replace the saturated synthetic filter. · Fix the new synthetic filter using the retaining clips and close the filter holder frame. GB 16 Odour filters (Recirculation version) REPLACING ACTIVATED CHARCOAL FILTERS · These filters are not washable and cannot be regenerated, and must be replaced approximately every four months of operation, or more frequently with heavy usage. · Remove the metal grease filters, or open the filter retaining grill. · Remove the saturated activated carbon filters by releasing the fixing hooks. · Fit the new filters by hooking them into their seating. · Replace the metal grease filters, or close the filter retaining grill. Lighting LIGHT REPLACEMENT · 20 W halogen light. · Remove the 2 Screws fixing the Lighting support, and pull it out of from the Hood. · Extract the Lamp from the Support. · Replace with another of the same type, making sure that the two pins are properly inserted in the lamp holder socket holes. [. . . ] · Extract the Lamp from the Support. · Replace with another of the same type, making sure that the two pins are properly inserted in the lamp holder socket holes. · Replace the Support, fixing it in place with the two Screws removed as above. · 40 W incandescent light · Remove the metal grease filters, or open the filter retaining grill. · Unscrew the bulbs and replace them with new ones having the same characteristics. [. . . ]