User manual ZANKER NOVELLA90/2MX

[. . . ] Crockery and cutlery B On/Off 30 g / ** Quick wash 65°C Light soil. Partial load (to be completed later in the day). C On/Off 30 g / Main wash up to 65°C 1 cold rinse 1 hot rinse Rinse and Hold D On/Off / / 1 cold rinse (to avoid food scraps from sticking together). * Testing programme for EN 50242. (see "Hints for test centres"). ** This is a speciaal programme for quick washing a full load of lightly soiled dishes, glasses and crockery (except pots) so that you may re-use promptly. 10 Operating sequence 1. [. . . ] Check the filters Ensure that they are clean and properly positioned. (See "Maintenance and cleaning" - Instruction book - Part 1) 9. At the end of the washing programme At the end of the programme the dishwasher will automatically stop. The On/Off indicator light remains on until the On/Off push button is depressed. 2. Check that there is rinse aid and salt (See Instruction book - Part 1) 10. Switch off the dishwasher Switch off the dishwasher by pressing the On/Off push button. Wait 15/20 minutes before opening the dishwasher's door; in this way you will avoid burning yourself when removing the dishes and avoid also the damage of the nearby furniture caused by the escape of steam. Empty the lower basket first and then the upper one; this will avoid water dripping from the upper basket onto the dishes in the lower one. 3. Load the dishes Remove any scraps of food. Cutlery should be placed in the removable cutlery basket with the handles facing downwards. If the handles protrude from the bottom of the basket, obstructing the lower spray arm, load the cutlery with the handles facing upwards. Mix spoons with other cutlery to prevent them from sticking together. Silver cutlery tends to go black if mixed with steel cutlery. Place it in the cutlery basket separate from the others. UI04 12 The upper basket The upper basket is designed for plates (dessert plates, saucers, dinner plates of up to 25 cm in diameter), salad bowls, cups and glasses. Arrange items so that water can reach all surfaces. Light items (plastic bowls etc. ) should be loaded in the upper basket and arranged so they do not move. In case that plates are loaded in the upper basket: load them starting from the rear positions of the basket; tilting them slightly forwards and avoiding the front positions near the door. US64 Before closing the door, ensure that the spray arms can rotate freely. US71 Adjusting the height of the upper basket If washing very large plates (over 27 cm and up to 32 cm in diameter) you can load them in the lower basket after moving the upper basket to the higher position. To move to the higher position proceed as follows: 1. Move the front runner stops (A) of the upper basket outward and slide the basket out. [. . . ] To move to the higher position proceed as follows: 1. Move the front runner stops (A) of the upper basket outward and slide the basket out. Refit the basket in the higher position and replace the stops (A) in their original position. RC01 A When the top basket is in the higher position it will only take plates up to 20 cm in diameter and you will not be able to use the cup racks. After loading your machine always close the door, as an open door can be a hazard. 13 Hints for test centres Before starting any test it is necessary to fill completely with salt the salt container and with rinse aid the rinse aid dispenser. Test standard: Reference programme: Load: Rinse aid selector: Detergent dosage: EN 50242 Normal 65°C with prewash 12 standard place settings position 5 25 g in the dispenser 5 g on the dispenser lid Arrangement upper basket Arrangement lower basket Technical specifications Dimensions Width Height with worktop Height without worktop Max depth Max depth with open door Voltage 60 cm 85 cm 82 cm 60 cm 115. 2 cm 230 V - 50 Hz 200 W 2100 W 2300 W 50 kPa (0. 5 bar) 800 kPa (8 bar) cold 12 place settings Electrical connection Motor rating during wash Power of heating element Overall power Water supply pressure Water supply connection Capacity Minimum Maximum Water cold/hot 14 Fitting under a counter (kitchen worktop or sink) By removing the machine's worktop, you can install it under a close fitting sink unit or a pre-existing top, providing the dimensions of the recess correspond to those shown in the picture. [. . . ]