User manual ZANKER ZKS5650IL

[. . . ] Geschirrspüler Dishwasher ZKS 5650 IL D GB Bedienungsanleitung Instruction book Seite 2 page 21 Contents Safety instructions Disposal Economical and ecological dishwashing Installation instructions Building-in Levelling Fixing to adjacent units Water supply connections Water inlet hose with safety valve Water outlet hose connection Electrical connection Description of the appliance The control panel Audible signals Prior to using for the first time The water softener Filling with dishwasher salt Rinse aid In daily use Loading cutlery and dishes The lower basket The cutlery basket The upper basket Use of detergent Different kinds of detergent Washing programmes Starting a washing programme 22 22 22 23 23 23 23 23 23 24 24 25 25 26 27 27 28 29 30 30 31 31 31 32 33 34 35 Maintenance and cleaning Cleaning the filters Prolonged periods of non-operation Frost precautions Moving the machine What to do, when. . . Service and spare parts Hints for test centres 36 36 36 36 36 37 38 39 Technical specifications Dimensions Width Height Max depth Max depth with open door 59. 6 cm 86. 8 - 94. 8 cm 55. 5 cm 119 cm Electrical connection: Voltage Overall power Fuse Water supply pressure Information on the electrical connection is given on the rating plate on the inner edge of the dishwasher's door. Minimum Maximum 50 kPa (0. 5 bar) 800 kPa (8 bar) 12 place settings Capacity This appliance complies with the following E. E. C. Directives: - 73/23 or 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 or 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. 21 Safety instructions It is most important that this instruction book should be retained with the appliance for future reference. [. . . ] In this case the rinse aid dispenser must be deactivated in orderto avoid a double dosage. Filling with rinse aid 1. Open the container by pressing the release button (A). Add the rinse aid until the container is completely full. The maximum level for filling is indicated by "max". Deactivation/activation of the rinse aid dispenser (The dishwasher must be switched off) Factory setting: rinse aid dispenser activated When the rinse aid dispenser has been deactivated, also the rinse aid indicator light on the control panel is automatically deactivated. All programme selection buttons indicator lights will illuminate (setting mode). If only one programme selection button indicator light is illuminated, this means that a washing programme has been selected. The programme must be cancelled: press simultaneously the function buttons 2 and 3 for about 2 seconds, the indicator light of the set programme button starts flashing for about 2 seconds. After about 2 seconds the indicator lights of all the programme selection buttons will illuminate indicating that the set programme has been cancelled and that the machine is now in setting mode. Press simultaneously function buttons 2 and 3, the indicator lights of the function buttons 1, 2 and 3 start flashing. Press the function button 2, the indicator lights of function buttons 1 and 3 turn off while the indicator light of the button 2 goes on flashing, at the same time the End indicator light illuminates, indicating that the rinse aid dispenser is active. To deactivate the rinse aid dispenser, press again the function button 2, the End indicator light turns off, indicating that the rinse aid dispenser has been deactivated. To memorise the operation, switch off the dishwasher by pressing the On/Off button or wait about 60 seconds after which the dishwasher will automatically return to setting mode. To activate again the rinse aid dispenser simply follow the above operations until the End indicator lights illuminates. Ensure that the lid is closed after every refill. Clean up any rinse aid spilt during filling with an absorbent cloth to avoid excess foaming during the next wash. Only use branded rinse aid for dishwashers. Never fill the rinse aid dispenser with any other substances (e. g. dishwasher cleaning agent, liquid detergent). This would damage the appliance. Adjusting the dose According to the finish and drying results obtained, adjust the dose of rinse aid by means of the 6 position selector (position 1 minimum dosage, position 6 maximum dosage). Increase the dose if there are drops of water or lime spots on the dishes after washing. Reduce it if there are sticky whitish streaks on the dishes or a bluish film on glassware or knife blades. Top up the rinse aid when the indicator light on the control panel illuminates. 29 In daily use q Check if it's necessary to refill with dishwasher salt or rinse aid Load cutlery and dishes into the dishwasher. Select a wash programme suitable for the cutlery and dishes. Start the wash programme. Loading cutlery and dishes Sponges, household cloths and any object that can absorb water may not be washed in the dishwasher. q q q q q Before loading the dishes, you should: - Remove large left-overs. [. . . ] The programme will continue from the point at which it was interrupted. If the fault code reappears contact your local Service Force Centre. For other combinations of fault codes not described in the above chart will appear, please contact your local Service Force Centre. . . . there are problems when operating the dishwasher Fault Possible cause The dishwasher door has not been properly closed. The programme does not start The main plug is not plugged in. [. . . ]