User manual ZANUSSI ADVANTAGE400

[. . . ] WASHING MACHINE AUTOMATA MOSÓGÉP AUTOMATICKÁ PRÁCKA AUTOMATICKÉ PRACKY INSTRUCTION BOOKLET HASZNÁLATI ÚTMUTATÓ NÁVOD NA OBSLUHU NÁVOD K OBSLUZE 35. 292. 617/0 CONTENTS Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unpacking and installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transit security bars. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] s If the appliance is to stand on a carpeted floor make sure that there is space between the carpet and the supporting feet of the appliance for the air to circulate freely around . s Care must be taken to ensure that the appliance does not stand on the electrical supply cable. 3 ENGLISH UNPACKING AND INSTALLATION TRANSIT SECURITY BARS Before starting the machine up, the transport security bars must be removed as follows: You are advised to keep all the transport security bars in case the appliance has to be transported again. Unscrew and remove the three rear screws by means of a key. HYDRAULIC CONNECTION There should be a COLD WATER tap near the washing machine with a screwing on connection pipe of 3/4 gas for the water supply, a sink, a wash basin or a drainage system in the wall. Previously check if: -- -- it is not a hot water tap. If not, run off a reasonable amount of water to flush out any debris that may have collected in the pipes. Have the permanent drainage system in the wall checked by a plumber. Place the enclosed rubber joint, delivered in a plastic bag together with the appliance (A), at the very end of the inlet hose and carefully screw the pipe to the tap taking care not to damage the screwdrive and fix the nut well on to the end in order to avoid leaking. If necessary turn the hose adequately by unscrewing the nut at the rear of the appliance. 2. Lean the appliance back on the rear and fit one of the polystyrene angles between the appliance and the floor. Make sure the hoses are not squashed. 3. Carefully remove the plastic bags on the right and the left, pulling them to the centre of the appliance. Now tighten the nut anew to avoid leaks. (Open the tap and asure that it does not leak and close it again. ) Place the discharging hose in a washbasin or sink with the aid of the bent piece delivered separately. The bent piece has to be entered into the tube's mouth in order to assure the support. Aforesaid piece allows the hose to be fixed to the wall by means of an opening on the upper part and that way the hose does not move and its falling is avoided. 4. Place the machine in an upright position and remove the three plastic bolts. 5. Plug the 3 holes with the plastic plugs which you can find in the envelope containing the instruction booklet. 4 IMPORTANT: The distance from the floor to the highest part of the hose should be between 60 to 90 cm. (It is advised to be between 60 and 70 cm). The hose must not be bent nor twisted to avoid clogging. Should a prolongation of the discharging hose be unavoidable this must never surpass 1. 5 m and must be of the same diameter as the original hose. «Wash» symbol shows the compartment for the washing detergent. «smooth» symbol shows the compartment for the smoothing additives. 2. ON/OFF LAMP It lights when the appliance is operating. 3. "E" BUTTON Pressing this button the programs stated with 90°C will be realized at 60°C. [. . . ] * Turn off the water tap and unscrew the inlet hose. * Select a wash program and run for a few seconds. * Position the end of the drain hose in a bowl on the floor. * Run the draining program for a few seconds. [. . . ]