User manual ZANUSSI CH91B

[. . . ] Customer Care Department Electrolux 55 - 77 High Street Slough Berkshire SL1 1DZ Tel: 08705 950 950 To register ownership, please ensure you complete and return the guarantee card supplied with the appliance. For the User Important Safety Information Your Appliance Operating Instructions Cooker Hood Controls To Operate Recirculation Extraction Maintenance and Cleaning External Cleaning Metal Grease Filters Charcoal Filters To Remove/Replace the Charcoal Filters Changing the Light Bulb For the Installer Technical Information Electrical Connection Electrical Requirements Electrical Connection Installing the Cooker Hood Installation Requirements Unpacking Clearance Heights Fitting the Wall Brackets Fitting the Canopy Hood Venting Recirculation Fitting the Chimney Stack Service Force Centres Something Not Working Service and Spare Parts Guarantee Conditions Guide to use the instruction book The following Symbols will be found in the text to guide you through the instruction book Safety instructions Step by step instructions 2 IMPORTANT SAFETY INFORMATION These warnings are provided in the interests of safety. Ensure that you understand them all before installing or using this appliance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. · · Installation Any installation work must be undertaken by a qualified electrician or a competent person. [. . . ] This appliance can be a possible fire hazard if the grease and charcoal filters are not cleaned and replaced as recommended. Fig. 2 Changing the Light Bulb 1. The light bulbs can be reached from inside the canopy. Rotate the light bulb anticlockwise to unscrew. To replace the light bulb insert a replacement into the holder then rotate the bulb clockwise into position. Ensure you take care not to overtighten the bulb. If the light bulb fails to function check that the bulb is fully screwed into the holder. If bulb failure has occurred then it should be replaced with a 220240 Volt 40W clear globe shaped bulb with a small E14 screw thread. Replacement filters and light bulbs can be obtained from your local Service Force Centre. 7 SOMETHING NOT WORKING If, having followed these instructions carefully, your cooker hood fails to work properly please carry out the following checks. Symptom The cooker hood will not start Solution · Check the hood is connected to the electricity supply. · Make sure the switch is in the `ON' position. · The fan speed is set high enough for the task · The grease filter is clean. · The kitchen is adequately vented to allow the entry of fresh air. · If set up for recirculation, check that the charcoal filter is still effective. France Germany Italy Sweden United Kingdom Senlis Nurnberg Pordenone Stockholm Slough +33 (0)3 44 62 22 22 +49 (0)911 323 2600 +39 (0)1678 47053 +46 (0)20 78 77 50 +44 (0)1753 219 898 9 INSTALLATION INSTRUCTIONS Technical information DIMENSIONS HEIGHT OF CANOPY: HEIGHT OF CHIMNEY:(UPPER SECTION) (LOWER SECTION) WIDTH OF CANOPY: CH 60 CH 90 DEPTH OF CANOPY: VOLTAGE: (~50Hz) POWER CONSUMPTION: FAN MOTOR: LAMPS: (2 x40W) 270mm 215mm 530mm 598mm 898mm 490mm 220-240V 225W 145W 80W ELECTRICAL SUPPLY SUITABLE FOR INSTALLATION ABOVE: ELECTRIC HOB: GAS HOB: SLOT-IN ELECTRIC COOKER: SLOT-IN GAS COOKER: 7KW (MAX) 10KW (MAX) 12. 4KW (MAX) 13. 5KW (MAX) Note: CE Marking certifies that this appliance complies with the requirements laid down in EEC directive 89:336 (Electromagnetic compatibility) and subsequent modifications and Low Votage directive 72/23/E. THIS APPLIANCE MUST BE EARTHED Electrical Requirements Any permanent electrical installation must comply with the latest I. E. E. Regulations and local Electricity Board regulations. For your own safety this should be undertaken by a qualified electrician e. g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC). This appliance is fitted with a 3 core mains cable and must be permanently connected to the electricity supply via a double-pole switch having 3mm minimum contact gap on each pole. A minimum clearance height of 650mm (25 ins) is required when installed above a built-in electric hob, or 700mm (27 ins) when installed above a built-in gas hob. A minimum clearance height of 685mm (27 ins) is required when installing above a slot-in electric cooker, or 787mm (30 ins) when installed above a slot-in cooker. When installed between adjoining wall cabinets, the wall cabinets must not overhang the hob and the distance between the underside of the cabinet and the worktop must be 450mmm (17 ins), a gap of 50mm (2 ins) must be maintained either side of the hob. This cooker hood must not be installed above a cooking appliance with a high level grill. Fitting the Wall Brackets 1. Draw a vertical line on the wall, from the centre of the cooking appliance up to the ceiling, using a spirit level and marker pen. This is to ensure the correct vertical alignment of the appliance. [. . . ] Note: If the hood is to be installed onto a hollow construction or plaster or partition board wall then special fixing screws will be required (not supplied). 4. 5. Fig. 4 13 Fitting the Canopy Hood 1. Adjust the two screws V on the top of the canopy to about halfway as illustrated in Fig. Hook the canopy onto the wall bracket 1 and push down until the canopy adjusting screws V rest on the bracket, turn the screws to adjust the canopy vertically and level it horizontally as illustrated in Fig. Insert the screw V1 into the central hole to lock the canopy in to position as illustrated in Fig. [. . . ]